| Author |
Message |
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
 Re: Make Your Own ....2CV.... 4x4 Not that many days and its going to be very cold next week:)
|
| February 22nd, 2018, 8:57 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 877
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4 10mm.'s better than nowt! now the workshop's spotless, Crack on  . subarupete wrote: Ooh clean floor!. Fitted the front diff prop shafts, they fit but very tight near the gearbox about 10mm clearance. Attachment: IMG_2061 (1).jpg
|
| February 22nd, 2018, 8:59 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Unexpected problems do occur or is it bad planning:) The input shaft to the remote gearbox had some play, had a look at the seal found it was a bad condition. Chevronics do a seal (££££) for GS/GSA boxes but the LN is about 1.5mm larger! So a bit of milling it was substituted sealed bearing. We will have to see if its OK. Input Shaft. Attachment:
IMG_2065.jpg [ 71.65 KiB | Viewed 6404 times ]
Old Seal. Attachment:
IMG_2062.jpg [ 74.1 KiB | Viewed 6404 times ]
New Bearing in place. Attachment:
IMG_2064.jpg [ 71.86 KiB | Viewed 6404 times ]
|
| February 23rd, 2018, 7:33 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 The list of things to do, should get shorter. However it seems that the plan to use a standard exhaust with cross-box wont fit:( Bigger calipers + the rear plate of the diff gets in the way. Attachment:
IMG_2084.jpg [ 94.98 KiB | Viewed 6388 times ]
Plan to fabricate an exhaust from mandrel bends...2 into 1 very sporty? Red lines show the plan, but as we are all very aware "Red Lines" can change or even disappear!!! Attachment:
IMG_2080.jpg [ 478.88 KiB | Viewed 6388 times ]
|
| February 26th, 2018, 2:52 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Can't make the exhaust till the body is sitting on the chassis and can't do that until I have a transfer shaft fitted. What is required, "the middle part". But, not happy with getting it welded. Attachment:
IMG_2111.jpg [ 298.07 KiB | Viewed 6316 times ]
So have to machine one!! Purchased a bit of steel.. Attachment:
IMG_2130.jpg [ 252.62 KiB | Viewed 6316 times ]
Some difficult milling/turning/drilling and lot of Google. Bit of a challenge but nothing ventured.....
|
| March 18th, 2018, 11:03 am |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2847
Location: NL
|
Re: Make Your Own ....2CV.... 4x4 Did you go to Morvan??
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| April 8th, 2018, 11:19 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Hi Geo,
Nope, the car was not finished:(
|
| April 9th, 2018, 8:31 am |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2247
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Hi all, Back again after a long period of no work on the off-road car or the road car. Turning & Milling required to join the two uj's to make the shaft between the clutch shaft and the remote gearbox. Attachment:
IMG_2112.jpg [ 317.37 KiB | Viewed 5914 times ]
Attachment:
IMG_3436.jpg [ 140.12 KiB | Viewed 5914 times ]
|
| August 2nd, 2018, 10:11 am |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 877
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4 Good to see you back on it Pete  .
|
| August 2nd, 2018, 10:14 pm |
|
|
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1634
Location: Exeter, Devon
|
Re: Make Your Own ....2CV.... 4x4 Yep +1 
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| August 2nd, 2018, 10:52 pm |
|
|
