| 
 
 
 
	
	
		
			|   | Page 1 of 1 
 | [ 9 posts ] |  |  
        
        
            | Author | Message |  
			| rustygubber Firing on two. 
					Joined: August 26th, 2011, 6:38 pm
 Posts: 114
   |   tickoverMy 2 2cv has been running fine for ages,till this week when it stoped ticking over,then it ticked over again ok,now it wount tick over at all and really low revs are lunpy,a little bit revs and it goes fine,still starts ok,im thinking blocked idle jet or dirt in carb,still using it daily,wount get chance to look at it till sunday,anyone else had same symptoms    
 
 |  
			| May 2nd, 2013, 9:59 pm | 
					
					   |  
		|  |  
			| Nelsthebass Firing on two. 
					Joined: October 5th, 2009, 8:22 pm
 Posts: 1415
 Location: Stone, Staffs
   |   Re: tickoverSounds very much like crap in the idle jet - check return spring hasn't gone AWOL too, or the throttle stop screw hasn't  wound itself down _________________
 1987 2CV Special
 2014 Suzuki Swift Sport
 2015 Lexus NX300h
 1966 Ami Break
 
 
 |  
			| May 2nd, 2013, 10:11 pm | 
					
					   |  
		|  |  
			| rustygubber Firing on two. 
					Joined: August 26th, 2011, 6:38 pm
 Posts: 114
   |   Re: tickoverThanks for reply,and pointers  
 
 |  
			| May 2nd, 2013, 10:18 pm | 
					
					   |  
		|  |  
			| Terry Firing on two. 
					Joined: November 4th, 2009, 4:00 pm
 Posts: 526
 Location: Confederate state of South Yorkshire
   |   Re: tickoverQuick 10 minute cure [if it is the idle jet]  .....     Take the rubber  "air filter to carb"  wotsit off   .......rev the engine and while its revving put the palm of your hand firmly over the top of the carb ....until the engine stalls. If theres any crap in the idle jet it'll dislodge it. And if youre one of those people who dont like getting yer hands dirty .....dont attempt to do it with rubber gloves on ....     hth T._________________
 Remember .....the drive is the reason,the destination is just the excuse.
 2CV6 Special [Red]
 C4 VTR+ Coupe [Black]
 C1 UrbanRide[Blue & Orange] {Ltd Ed}
 
 
 |  
			| May 2nd, 2013, 11:04 pm | 
					
					   |  
		|  |  
			| Luke Firing on two. 
					Joined: December 9th, 2008, 7:50 pm
 Posts: 662
   |   Re: tickoverIn my experience that's great for the primary and secondary jets, but doesn't do much fir the idle jet. It only takes a few seconds to remove the idle jet, though, it's the 8mm hex head with the screwdriver slot, and is near the top at the front. Easier undone with spanner than a screwdriver. 
 
 |  
			| May 2nd, 2013, 11:41 pm | 
					
					   |  
		|  |  
			| ken Agony Aunt - You have a car problem? Speak to Ken 
					Joined: March 6th, 2009, 1:40 am
 Posts: 3675
   |   Re: tickoverLuke, yep, it tends to embed any debris that's already lodged in the tiny drilling even deeper. (less than 0.4mm diameter for the idle jet)  Luke wrote: In my experience that's great for the primary and secondary jets, but doesn't do much fir the idle jet. It only takes a few seconds to remove the idle jet, though, it's the 8mm hex head with the screwdriver slot, and is near the top at the front. Easier undone with spanner than a screwdriver._________________
 
   
 
 |  
			| May 2nd, 2013, 11:58 pm | 
					
					   |  
		|  |  
			| J-dub Aircooled Idiot 
					Joined: April 24th, 2010, 10:01 am
 Posts: 5733
 Location: Location Location
   |   Re: tickoverIll always remove a blocked jet to clean. You know its 100% clear _________________
 
  
 1988 2cv 652cc
 1993 Toyota Hilux Surf 3000cc runs on Bio Diesel
 2004 Toyota Landcruiser Amazon 4200cc runs on Bio Diesel
 1998 Daihatsu Hijet 1300cc
 2005 Susuki Bandit 650cc
 
 
 |  
			| May 3rd, 2013, 12:09 am | 
					
					     |  
		|  |  
			| rustygubber Firing on two. 
					Joined: August 26th, 2011, 6:38 pm
 Posts: 114
   |   Re: tickoverThanks for all replies,cant get to my spanners till sunday,so ill let you know how i get on, and my hands are alway dirty    
 
 |  
			| May 3rd, 2013, 8:10 am | 
					
					   |  
		|  |  
			| rustygubber Firing on two. 
					Joined: August 26th, 2011, 6:38 pm
 Posts: 114
   |   Re: tickoverGot to work on it this morning,removed jet 1st,removed a large piece muck,washed and blown out,refitted,ticks over a treat,done a few other niggling jobs,then went on a 80 mile round trip with the roof down,didnt miss a beat,    thanks for all advise  
 
 |  
			| May 5th, 2013, 8:39 pm | 
					
					   |  
		|  |  
	
		
			|   | Page 1 of 1 
 | [ 9 posts ] |  |  
 
	
		| Who is online |  
		| Users browsing this forum: No registered users and 648 guests |  
 
	|  | You cannot post new topics in this forum You cannot reply to topics in this forum
 You cannot edit your posts in this forum
 You cannot delete your posts in this forum
 You cannot post attachments in this forum
 
 |  
   |