View unanswered posts | View active topics It is currently May 13th, 2025, 11:10 pm



Reply to topic  [ 15 posts ]  Go to page 1, 2  Next
 Oil cooler cleaning 
Author Message
Aircooled Idiot
User avatar

Joined: April 24th, 2010, 10:01 am
Posts: 5733
Location: Location Location
Post Oil cooler cleaning
Whats the most efficiant way to loose and remove this black oily shit without hurting the find??

Image

Bit of petrol / aceton on a rag and gently rub and then blow through with compressed air?

Thanks

_________________
Image

1988 2cv 652cc
1993 Toyota Hilux Surf 3000cc runs on Bio Diesel
2004 Toyota Landcruiser Amazon 4200cc runs on Bio Diesel
1998 Daihatsu Hijet 1300cc
2005 Susuki Bandit 650cc


January 27th, 2013, 8:51 pm
Profile WWW
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: Oil cooler cleaning
Leave it until warmer temp. You need every bit of heat to keep the oil at working temp.

_________________
Image


January 27th, 2013, 9:19 pm
Profile WWW
Firing on two.

Joined: April 27th, 2012, 6:48 pm
Posts: 709
Post Re: Oil cooler cleaning
i posted the same question a few weeks ago, ken repled that its very important to keep them clean or the oil can overheat on long runs
compressed air and a good attatchment to blast the crud away is good


January 27th, 2013, 9:42 pm
Profile
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: Oil cooler cleaning
ayjay wrote:
i posted the same question a few weeks ago, ken repled that its very important to keep them clean or the oil can overheat on long runs
compressed air and a good attatchment to blast the crud away is good



No not in temps below 0. Ask the Finnish, they block the oil cooler completely during winter and their engines never suffer from over heating. Yes if the temp crawls above +5

_________________
Image


January 27th, 2013, 9:47 pm
Profile WWW
Firing on two.
User avatar

Joined: November 4th, 2009, 4:00 pm
Posts: 526
Location: Confederate state of South Yorkshire
Post Re: Oil cooler cleaning
I use aerosol engine degreaser [available from such as Halfrods,or even cheaper in y' local Poundland /Poundworld/99p store] .......just spray it on and then brush the fins with a soft paintbrush .....then shift whats left with compressed air.

2CViking wrote:
Leave it until warmer temp. You need every bit of heat to keep the oil at working temp.

:? Strange ......I thought the grille muff was supposed to do that......I overheated my engine on a cold November evening a coupla years ago whilst driving [somewhat quickly] up the A1 .....[resulting in a cracked head,a scored barrel,broken rings & fubar'd piston].
Fortunately,Uncle Ken rebuilt my engine.
IMHO,late model engines [the ones with with the plastic cooling shrouds/cowlings] need all the help they can get to stay cool.

best regards
T.

_________________
Remember .....the drive is the reason,the destination is just the excuse.
2CV6 Special [Red]
C4 VTR+ Coupe [Black]
C1 UrbanRide[Blue & Orange] {Ltd Ed}


January 27th, 2013, 9:53 pm
Profile
Firing on two.
User avatar

Joined: December 26th, 2008, 9:40 pm
Posts: 3332
Location: Surrounded by 2cvs...
Post Re: Oil cooler cleaning
2CViking wrote:
Yes if the temp crawls above +5


James isn't Finnish. Here in the UK for the temp to be guaranteed to stay below 5deg for more than a few days at a time is rare.

I'd go a bit further than Terry - rather than just a soft paintbrush, an old toothbrush won't hurt and will get more shifted. Degreaser, brake cleaner, carb cleaner - whatever solvent's to hand.

_________________
Image
Zookeeper of a miscellany of motorised silliness - from 0.75bhp to 9ft tall - now living life on the road in an old VW.
http://WhereverTheRoadGoes.com


January 27th, 2013, 10:24 pm
Profile YIM WWW
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: Oil cooler cleaning
Alright then clean it :mrgreen:

_________________
Image


January 27th, 2013, 10:26 pm
Profile WWW
Aircooled Idiot
User avatar

Joined: April 24th, 2010, 10:01 am
Posts: 5733
Location: Location Location
Post Re: Oil cooler cleaning
Thanks boys

I hae some gunk at work. Ill use that and a toothbrush
Shall report back.

_________________
Image

1988 2cv 652cc
1993 Toyota Hilux Surf 3000cc runs on Bio Diesel
2004 Toyota Landcruiser Amazon 4200cc runs on Bio Diesel
1998 Daihatsu Hijet 1300cc
2005 Susuki Bandit 650cc


January 27th, 2013, 10:35 pm
Profile WWW
Agony Aunt - You have a car problem? Speak to Ken

Joined: March 6th, 2009, 1:40 am
Posts: 3675
Post Re: Oil cooler cleaning
James,
make that a soft toothbrush.
Best way I've found is a paraffin gun (or old spray gun) filled with petrol, followed up
with the air blow gun.

A pressure washer is definitely out, as that's the quickest route to distorted fins.

ken


Jameswallace wrote:
Thanks boys

I hae some gunk at work. Ill use that and a toothbrush
Shall report back.

_________________
Image


January 27th, 2013, 10:52 pm
Profile
Firing on 1-2 Spark
User avatar

Joined: November 8th, 2009, 5:42 pm
Posts: 2847
Location: NL
Post Re: Oil cooler cleaning
I always use compressed air, airgun?? aiming from the backside of the oilcooler to the fanside, so oil and dirt goes out the same way as it goes in....... watch out the louvres are in a 30? degrees angle at a 2cv6.
Please do this all with a soft touch.... You can easily destroy an oilcooler!!!!!!!!!!

_________________
Russell wrote:
Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ


January 27th, 2013, 11:54 pm
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 15 posts ]  Go to page 1, 2  Next

Who is online

Users browsing this forum: No registered users and 110 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.