| Author |
Message |
|
db78
Firing on two.
Joined: August 19th, 2013, 7:16 pm
Posts: 123
|
 2cv gearbox length Hi, Roughly how long in a 2cv6 gearbox? from front face of bell housing to most rearward point and also if possible the width between the drive shaft flanges. 
|
| September 4th, 2013, 8:16 pm |
|
|
|
toomany2cvs
Firing on two.
Joined: December 26th, 2008, 9:40 pm
Posts: 3332
Location: Surrounded by 2cvs...
|
Re: 2cv gearbox length db78 wrote: Hi, Roughly how long in a 2cv6 gearbox? from front face of bell housing to most rearward point and also if possible the width between the drive shaft flanges. <rummages in back of ill-lit shed> From front of bellhousing to gearbox mount, about 450mm. If you include the input shaft, more like 480. Width - about 350.
_________________
Zookeeper of a miscellany of motorised silliness - from 0.75bhp to 9ft tall - now living life on the road in an old VW.
http://WhereverTheRoadGoes.com
|
| September 4th, 2013, 8:54 pm |
 
|
|
|
Sean
Firing on two.
Joined: April 22nd, 2009, 11:06 pm
Posts: 3684
Location: Ecosse
|
Re: 2cv gearbox length ive got a shorter one if you need it, only ran 23'35" since a re build, bell housing is a bit of a mess.  bit of an issue
_________________
Kissing the Lash
"Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
Last edited by Sean on September 5th, 2013, 7:59 am, edited 2 times in total.
|
| September 4th, 2013, 9:46 pm |
|
|
|
Russell
Firing on two.
Joined: November 29th, 2008, 10:05 pm
Posts: 9259
Location: West Sussex, U.K.
|
Re: 2cv gearbox length I wish I'd seen it go. Must've been like a grenade going off. Did you get all of the flywheel back? Could you weld it back together? No issues.
_________________
samfieldhouse wrote: What I like about I2F is that there is no pretence of democracy.
|
| September 4th, 2013, 10:21 pm |
|
|
|
Sean
Firing on two.
Joined: April 22nd, 2009, 11:06 pm
Posts: 3684
Location: Ecosse
|
Re: 2cv gearbox length cast so welding difficult "JB weld" is better! "As strong as a weld" and i can "machine and tap it just like metal" in fact im just going to buy 100 tubes and make a JB flywheel
_________________
Kissing the Lash
"Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
|
| September 5th, 2013, 7:58 am |
|
|
|
J-dub
Aircooled Idiot
Joined: April 24th, 2010, 10:01 am
Posts: 5733
Location: Location Location
|
Re: 2cv gearbox length Looks like a broken egg
_________________
1988 2cv 652cc
1993 Toyota Hilux Surf 3000cc runs on Bio Diesel
2004 Toyota Landcruiser Amazon 4200cc runs on Bio Diesel
1998 Daihatsu Hijet 1300cc
2005 Susuki Bandit 650cc
|
| September 5th, 2013, 8:16 am |
|
|
|
db78
Firing on two.
Joined: August 19th, 2013, 7:16 pm
Posts: 123
|
Re: 2cv gearbox length toomany2cvs wrote: db78 wrote: Hi, Roughly how long in a 2cv6 gearbox? from front face of bell housing to most rearward point and also if possible the width between the drive shaft flanges. <rummages in back of ill-lit shed> From front of bellhousing to gearbox mount, about 450mm. If you include the input shaft, more like 480. Width - about 350. thank you Sean wrote: ive got a shorter one if you need it, only ran 23'35" since a re build, bell housing is a bit of a mess.
impressive! but aslo gutted for you running so close to the finish..
|
| September 5th, 2013, 7:14 pm |
|
|
