View unanswered posts | View active topics It is currently March 29th, 2024, 1:28 am



Reply to topic  [ 42 posts ]  Go to page 1, 2, 3, 4, 5  Next
 King pin tools 
Author Message
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post King pin tools
How to use the King pin tools.

This tool is so easy to use. It is very well made and long lasting. I have added a few ‘’tricks of the trade’’ to make it easier to change the king pin.

Open the folded over bottom cap. Clean the slot and gently tap the tool with a small hammer.
Attachment:
tool.JPG



Push the drift up through the middle of the king pin to reach the top grease/dust cap. Use the big hammer to hammer out the cap. Cover the cap with a rag to prevent it hitting the roof.

Attachment:
2.JPG


Attachment:
3.JPG



Now is the time to grind away the folded over edges holding the grease/dust cap. Should be done before removing the bush.

Attachment:
4.JPG



Clean all metal chips away.

Attachment:
5.JPG


Place a firm stand underneath the swing arm. Remove the grease nipple first


Attachment:
6.JPG



Place the drift and hit it with a big hammer and I mean BIG. Shock technique is the best way of removing a stuck king pin. Do NOT use heat at all.

Attachment:
7.JPG



Time to place the hub upside down in the vice. Push the bottom push out away from the thread. Not through the thread, you may ruin it.

Attachment:
8.JPG



Top bush next

Attachment:
9.JPG


This can be a problem. The old king pin was not greased at all. Metal against metal and you get this groove.

Attachment:
10.JPG


File it flat, so the new shim is seated against a flat face

Attachment:
11.JPG


Push in the bottom bush first. Remember to grease it.

Attachment:
12.JPG


Attachment:
13.JPG


Needs to be just below the face to avoid contact with the shim.

Attachment:
14.JPG



Top bush. Use the alignment tool for the top bush. Without this tool the bush can tilt when pushed in.

Attachment:
15.JPG


Attachment:
16.JPG


Very important that the bush is correctly aligned. It must not have any contact with swing arm.

Photo upside down.

Attachment:
17.JPG


Test the postion of both bushes by sliding the new king pin up and down. No biting at all.

Attachment:
18.JPG



Use the old king pin to align the shims etc.

Attachment:
19.JPG


After the correct shims are fitted (max 0.4 mm play between the hub and swing arm, use feeler gauges)

Attachment:
20.JPG


Gently tap the old king pin in to the swing arm. King pin must NOT be distorted.

Attachment:
21.JPG


Place the new king pin correctly and use this drift to push it in. Hold the old king pin so it doesn’t fall out.

Attachment:
22.JPG


Don’t forget the firm stand to support the swing arm

Stop when the top of the king pin is aligned with the top of the bush

Attachment:
23.JPG


Place the new cap, flatten the cap using the old king pin

Attachment:
24.JPG


Fold over the edges to lock the cap

Attachment:
25.JPG


Fit the bottom cap, grease nipple and grease the new king pin.

Check that the top cap is not pushed out. Seal the top cap with grease to prevent water getting in.

Attachment:
26.JPG


Maybe a sticky if the lordship agree.. :P


You do not have the required permissions to view the files attached to this post.

_________________
Image


February 27th, 2010, 4:03 pm
Profile WWW
Firing on two.
User avatar

Joined: August 18th, 2009, 10:31 pm
Posts: 1244
Location: Berkel-Enschot, Netherlands
Post Re: King pin tools
Just made it sticky!!

Really nice report for changing the kingpin. The only thing I miss is that you show in wich way the kingpin needs to be fitted ;)


Did you freeze in the new kingpin? I did it when I changed mine.. When you freeze it, the kingpin shrinks a bit so it fit's easier in the swingarm...

_________________
Image
1986 Citroen 2CV6 Special Pick-Up
1964 Solex Oto Van der Heem


February 27th, 2010, 4:46 pm
Profile WWW
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: King pin tools
Tom Duckpower wrote:
Just made it sticky!!

Really nice report for changing the kingpin. The only thing I miss is that you show in wich way the kingpin needs to be fitted ;)


Did you freeze in the new kingpin? I did it when I changed mine.. When you freeze it, the kingpin shrinks a bit so it fit's easier in the swingarm...


Thanks for making it a sticky. I hope ''bush mechanics'' can get some good use of it.
Yes I did miss how to place the pin in relation to the grease holes. Will take a photo soon.

No I've never frozen the pin. I like to ''feel'' how tight it goes in (sorry this sounds almost sexual) If the pin is too lose, I fit oversized pin of 17.1 mm.

Click to enlarge

Attachment:
King-pin-holes.jpg


You do not have the required permissions to view the files attached to this post.

_________________
Image


Last edited by 2CViking on February 27th, 2010, 6:30 pm, edited 1 time in total.



February 27th, 2010, 5:17 pm
Profile WWW
Old Bloke

Joined: May 25th, 2009, 11:39 am
Posts: 685
Post Re: King pin tools
Fantastic set of photos, I am sure there will be many people who will get great use out of them. Well done. :D

_________________
Now known as 602

http://www.2CVTech.co.uk


February 27th, 2010, 5:38 pm
Profile
Firing on two.
User avatar

Joined: November 29th, 2008, 10:05 pm
Posts: 9259
Location: West Sussex, U.K.
Post Re: King pin tools
Brilliant Viking, thanks very much for this, worn kingpins at MOT were one of the biggest 2cv killers in the UK at one time, it was easier and cheaper to buy another 2cv for a few pounds than pay a mechanic to do this, it's great to have it explained, thanks!

_________________
samfieldhouse wrote:
What I like about I2F is that there is no pretence of democracy.


February 27th, 2010, 7:26 pm
Profile
super slot
User avatar

Joined: November 28th, 2008, 11:14 pm
Posts: 8797
Location: Cornwall, UK
Post Re: King pin tools
grifftravel wrote:
Fantastic set of photos, I am sure there will be many people who will get great use out of them. Well done. :D


agreed. It's nice to have clear pictures to go with the text. :)

Nice one!

_________________
Image


February 27th, 2010, 7:35 pm
Profile WWW
Firing on two.
User avatar

Joined: January 26th, 2009, 10:16 pm
Posts: 1074
Location: Derbyshire
Post Re: King pin tools
Excellent set of photos - I've never tried the shock method. My dad made a replica of the press shown in the Haynes manuals when he rebuilt my first Dyane (24 years ago now).
I've still got it, so if anyone needs to borrow it let me know.

_________________
Image
Mr Early Night aka Snuff Pusher


February 27th, 2010, 10:09 pm
Profile
Firing on two.

Joined: February 12th, 2009, 6:17 pm
Posts: 316
Location: North
Post Re: King pin tools
Thanks Viking!
I've never done a kingpin myself, but have heard they can be so stuck you can't hit them out...
Is that something which wouldn't happen, when you use (these) right tools.
Or can it even with the right tool occur you can't get it out?
& what to do then???
Do the specialists have additional tricks for that?

Thanks Bart

_________________
Image


February 28th, 2010, 9:37 am
Profile WWW
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: King pin tools
Hi Bart
In my young days at the Citroën dealer ship, we removed the arm and pressed the king pins out but sometimes the pin wouldn't move. Applied heat but don’t do it and maybe the pin came out. I later moved on to a 2cv garage and the old rat running the business told me not to bother with the press or using heat. Since that day, I’ve removed all pins including really stuck pins with the shock technique, no worries. I’ve seen arms being ruined by excessive heat even seen people cutting the arm open to release the bitting on the pin. The only problem using force is the risk of expanding the top of the king pin (mushroom effect) when hitting it. The risk is reduced by using a drift which is softer than the king pin. The drift will expand so the trick is not to push the drift through the arm making the hole bigger. I clean the drift up on the bench grinder and continue, no harm done to the swing arm.

_________________
Image


February 28th, 2010, 10:39 am
Profile WWW
Firing on two.
User avatar

Joined: November 16th, 2009, 10:14 am
Posts: 211
Location: Aylesford, Kent
Post Re: King pin tools
Yes, it was with a feeling of trepidation that I replaced the O/S kingpin on Amélie a few months ago but it really was as straightforward as that post described. Silly CVs lent me a bag of assorted drifts and everything came apart pretty well. I think one mistake I made was not cleaning up the old staking on the top of the uprights. The new Welsh plug refused to seal and I damaged it with repeated hammering. After removing it and grinding away the old staking properly, the plug went back in. I shall do the N/S sometime and then keep both sides regularly greased.

_________________
Image


February 28th, 2010, 4:24 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 42 posts ]  Go to page 1, 2, 3, 4, 5  Next

Who is online

Users browsing this forum: No registered users and 82 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.