| Author |
Message |
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1600
Location: Exeter, Devon
|
 Re: Transfer box.. A new version... So how do you tension the chain?
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| November 2nd, 2023, 10:47 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Currently no tensioner , based on fixed shafts and this .. https://www.blocklayer.com/chain-sprocket.
|
| November 3rd, 2023, 9:40 am |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Try out for the additional shaft, with dog selector. Re-using a top shaft and the third gear dog selector parts. Ignore the large hole in the casing, this was an attempt to use gears like a Mehari 4x4. Attachment:
4x4 - 1 of 1.jpeg [ 283.88 KiB | Viewed 7268 times ]
|
| November 4th, 2023, 2:52 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Fabricated selector fork from 3rd gear items. Attachment:
Selector fork.jpeg [ 136.12 KiB | Viewed 7225 times ]
Extended synchronizer ring. Attachment:
Dog.jpeg [ 127.42 KiB | Viewed 7225 times ]
Sprocket. Attachment:
sprocket.jpeg [ 260.57 KiB | Viewed 7225 times ]
Tryout? Attachment:
4x4 - 1 of 1.jpeg [ 261.28 KiB | Viewed 7225 times ]
|
| November 9th, 2023, 5:16 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Got the 13 tooth sprocket, splined done with EDM (wire cut). Attachment:
4x4 - 1 of 2.jpeg [ 308.84 KiB | Viewed 7183 times ]
In situ on the top shaft. Attachment:
4x4 - 2 of 2.jpeg [ 239.76 KiB | Viewed 7183 times ]
|
| November 15th, 2023, 5:27 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Chain and sprockets in alignment, need to fabricate a a longer syncro/dog selector. Attachment:
Recents - 1 of 2.jpeg [ 311.38 KiB | Viewed 7139 times ]
Attachment:
Recents - 2 of 2.jpeg [ 255.97 KiB | Viewed 7139 times ]
|
| November 19th, 2023, 4:51 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Started to fabricate the rear cover, seems there is room for a trilpex chain:)? Attachment:
2.jpg [ 820.19 KiB | Viewed 7091 times ]
Attachment:
1.jpg [ 896.03 KiB | Viewed 7091 times ]
|
| November 25th, 2023, 3:14 pm |
|
|
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1600
Location: Exeter, Devon
|
Re: Transfer box.. A new version... So, where does this go?
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| November 25th, 2023, 4:37 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2241
Location: Near Monmouth
|
Re: Transfer box.. A new version... Will bolt onto the back of a standard gearbox. Attachment:
P1010758.jpeg [ 767.59 KiB | Viewed 7085 times ]
|
| November 25th, 2023, 5:45 pm |
|
|
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1600
Location: Exeter, Devon
|
Re: Transfer box.. A new version... So you remove the end plate of the standard gearbox?
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| November 25th, 2023, 6:32 pm |
|
|
