| Author |
Message |
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1654
Location: Exeter, Devon
|
 Re: We have liftoff.....AZU 250 rebuild thread Check you have 12v at the actual head/side lights. If you have, then it must be a ground issue.
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| October 7th, 2020, 3:00 pm |
|
|
|
48pop
Firing on two.
Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
|
Re: We have liftoff.....AZU 250 rebuild thread will check tonight......but odd that horn is still working 
|
| October 7th, 2020, 4:36 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2251
Location: Near Monmouth
|
Re: We have liftoff.....AZU 250 rebuild thread Horn is earthed via fixing nut?
|
| October 7th, 2020, 4:48 pm |
|
|
|
48pop
Firing on two.
Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
|
Re: We have liftoff.....AZU 250 rebuild thread Just been back out to garage.......All sorted happy days  Battery tray was out for access to back of speedo. to get it out I had loosened the vent....which also included the earth.....EEJIT ! 
|
| October 7th, 2020, 10:20 pm |
|
|
|
Geert
Firing on two.
Joined: July 10th, 2010, 12:35 pm
Posts: 1186
Location: Magyarország
|
Re: We have liftoff.....AZU 250 rebuild thread
_________________
'T is een kwestie van geduld.........
Ez a türelem kérdése.........
|
| October 8th, 2020, 7:34 am |
|
|
|
48pop
Firing on two.
Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
|
Re: We have liftoff.....AZU 250 rebuild thread Been a while ! dash all back in an nearly finished wiring.......Got my steering wheel cap done today. Started with a rough cut from some scrap 10mm plate.  Tickle with the grinder and add something for lathe mounting  My mates dad then added a step to fit boss using his 60yr old churchhill lathe. Then then I mounted in my drill, and added some shape with a 40grit flapwheel in the grinder...   
|
| November 7th, 2020, 8:07 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2251
Location: Near Monmouth
|
Re: We have liftoff.....AZU 250 rebuild thread Good results, like it.
|
| November 7th, 2020, 8:22 pm |
|
|
|
Geert
Firing on two.
Joined: July 10th, 2010, 12:35 pm
Posts: 1186
Location: Magyarország
|
Re: We have liftoff.....AZU 250 rebuild thread nice
_________________
'T is een kwestie van geduld.........
Ez a türelem kérdése.........
|
| November 8th, 2020, 9:34 am |
|
|
|
48pop
Firing on two.
Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
|
Non stopping wipers ! Hi folks, got caught in the rain today, wipers started fine, but.......even without switch, they wouldnt stop......
I swapped the dash recently, so assumed I'd got the switch wiring wrong , so I disconnected it,,,,,and they still wiped !
Found a few threads on here but I'm still unclear what i need to do !! Is there an easy guide ??????
(its the older, cheese grater type....)
Cheers !
Gerry
|
| November 21st, 2020, 11:12 pm |
|
|
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1654
Location: Exeter, Devon
|
Re: We have liftoff.....AZU 250 rebuild thread Is it one that parks? Or would you expect it to just stop where ever you turned it off?
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| November 21st, 2020, 11:52 pm |
|
|
