View unanswered posts | View active topics It is currently March 28th, 2024, 7:34 pm



Reply to topic  [ 183 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15, 16, 17 ... 19  Next
 We have liftoff.....AZU 250 rebuild thread 
Author Message
Firing on two.
User avatar

Joined: July 10th, 2010, 12:35 pm
Posts: 1091
Location: Magyarország
Post Re: We have liftoff.....AZU 250 rebuild thread
1974 ? It has no oil warning light. In my van there is an extra wire to fit a warninglight. ( original wiringloom )
Should not be too much work to fit one

_________________
'T is een kwestie van geduld.........


Ez a türelem kérdése.........


September 12th, 2020, 8:15 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
Yeah, I also have a spare wire at the front, but no light on the dash.....I'm assuming the accountants saved 20 centimes by leaving out the lamp on the dash !


September 12th, 2020, 8:55 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
Question: Would a '94 (correction '74) AZU250 have a "key start" or keyed ignition + start button ?

Looks like there has never been anything on the steering column

My wiring is a bit messed up, so currently I have a keyed ignition and a toggle switch to start


Last edited by 48pop on September 14th, 2020, 5:01 pm, edited 1 time in total.



September 14th, 2020, 3:51 pm
Profile
Firing on two.
User avatar

Joined: July 10th, 2010, 12:35 pm
Posts: 1091
Location: Magyarország
Post Re: We have liftoff.....AZU 250 rebuild thread
48pop wrote:
Question: Would a '94 AZU250 have a "key start" or keyed ignition + start button ?

Looks like there has never been anything on the steering column

My wiring is a bit messed up, so currently I have a keyed ignition and a toggle switch to start

In 1994 there where no 2cv Vans made anymore . ;) production ended in the ´70 s .
BUT :::: the 1974 van has a keyed ignition and a pushbutton to start. :D

_________________
'T is een kwestie van geduld.........


Ez a türelem kérdése.........


September 14th, 2020, 4:15 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
Oops, of course I meant '74 :)


September 14th, 2020, 5:00 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
nothing much to report.....

Played around with ride height and tyre pressures, now sitting pretty close to factory specs and 26PSI all round....still a little "crashy" over bumps.. any suggestions?

Fitted new heater/vent/dump pipes
Finally bought the Airfilter>carb pipe, Van is a heck of a lot quieter now with its airfilter fitted

Replaced notchy alternator with spare, made new backing for warped door card. Nearly choked on the cost of the wee silly trim clips....

Looking at my drivers door I'm missing the doorlock rod and, the connector at the lock end...so I still have to open window to get to the outside handle.....

I'll have to strip the lock from the other side so I can make the bit of the lever thats missing, and see if I can modify a later lock rod.......(unless someone has these bits lying around??

Its this style of lock and I "think" I'm missing the bit carefully drawn in red..... Can anyone confirm ? I can't find any diagrams...

Image

Been driving around locally till my confidence builds....


September 21st, 2020, 4:02 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
In fact, found a diagram on burton site but they don't seem to have the bits...

I think the rod is same as a later car but its number 10 I need (or need to make....)

Image


September 21st, 2020, 4:22 pm
Profile
Firing on two.

Joined: November 2nd, 2011, 12:35 pm
Posts: 583
Location: Charente-Maritime
Post Re: We have liftoff.....AZU 250 rebuild thread
48pop wrote:
nothing much to report.....

Played around with ride height and tyre pressures, now sitting pretty close to factory specs and 26PSI all round....still a little "crashy" over bumps.. any suggestions?



From personal experience, a full set of Michelin tyres goes a long way to smoothing out the ride and improving handling. This may seem an expensive luxury but worth every penny. Funnily enough, I had a very noisy engine cured by fitting of correct air filter. Seems they are (effectively) induction silencers as well.


September 21st, 2020, 5:10 pm
Profile
Firing on two.
User avatar

Joined: October 22nd, 2014, 10:59 pm
Posts: 1994
Location: South-Limburg
Post Re: We have liftoff.....AZU 250 rebuild thread
Are your friction dampers ok?
Unloaded 1.4 atm front, 1.8 rear ?


September 21st, 2020, 8:17 pm
Profile
Firing on two.

Joined: May 23rd, 2011, 7:14 pm
Posts: 309
Location: ecosse
Post Re: We have liftoff.....AZU 250 rebuild thread
Cockpit has always been a bit tight in the van due to my ample beer belly......

So, a day off today. With 90% of skills and equipment supplied by my mate Jack, we did this today :)

Roll up one of these

Image

Add some of this

Image

And one of these

Image

Measure carefully

Image

Add a bit of skilled welding

Image

And you have this !

Image

Gives me a bit more room to breathe :)
Image

Next is to get a nice wee cap turned up for the wheel and swap out the dash for a flat plate and MPH dial..... !


September 28th, 2020, 6:04 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 183 posts ]  Go to page Previous  1 ... 11, 12, 13, 14, 15, 16, 17 ... 19  Next

Who is online

Users browsing this forum: Bing [Bot] and 84 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.