| Author |
Message |
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
 Re: Make Your Own ....2CV.... 4x4 Discs now fitted and different brace (x2) allows drive shaft clearance. Attachment:
IMG_2007.jpg [ 291.57 KiB | Viewed 4550 times ]
Whoopee, only two oil leaks. Need a copper washer under the sump nut. Attachment:
IMG_2012.jpg [ 217.23 KiB | Viewed 4550 times ]
And a seal?? for the splined prop shaft flange?? Attachment:
IMG_2011.jpg [ 307.64 KiB | Viewed 4550 times ]
|
| February 9th, 2018, 12:54 pm |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2846
Location: NL
|
Re: Make Your Own ....2CV.... 4x4 subarupete wrote:
Whoopee, only two oil leaks.
Great job you did then...
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| February 9th, 2018, 2:16 pm |
|
|
|
jasu
Firing on two.
Joined: August 8th, 2012, 11:00 am
Posts: 480
Location: Korpilahti, Finland
|
Re: Make Your Own ....2CV.... 4x4 subarupete wrote: And a seal?? for the splined prop shaft flange?? On Land-Rover there is felt under the nut at flange. And many put also some sealing/glue to splines to avoid leaking... Nicely done when there isn't any other leaks..!
|
| February 9th, 2018, 3:04 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Thanks guys.
|
| February 9th, 2018, 3:51 pm |
|
|
|
jasu
Firing on two.
Joined: August 8th, 2012, 11:00 am
Posts: 480
Location: Korpilahti, Finland
|
Re: Make Your Own ....2CV.... 4x4  Part no 5 on that picture...
|
| February 9th, 2018, 4:05 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Something like this... Perhaps make it from felt or soft rubber? Attachment:
2_image.jpg [ 9.29 KiB | Viewed 4536 times ]
|
| February 9th, 2018, 5:08 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Fitted the centre bearing for the front prop shafts. Attachment:
IMG_2030.jpg [ 296.12 KiB | Viewed 4515 times ]
Shortened the first of two prop shafts, combination of suzuki/truimph-herald bits. Attachment:
IMG_2039.jpg [ 275.47 KiB | Viewed 4515 times ]
|
| February 15th, 2018, 5:15 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 The first on and even painted it... Attachment:
IMG_2052.jpg [ 292.8 KiB | Viewed 4502 times ]
|
| February 17th, 2018, 4:58 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2141
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Ooh clean floor!. Fitted the front diff prop shafts, they fit but very tight near the gearbox about 10mm clearance. Attachment:
IMG_2061 (1).jpg [ 84.88 KiB | Viewed 4480 times ]
|
| February 22nd, 2018, 5:17 pm |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2846
Location: NL
|
Re: Make Your Own ....2CV.... 4x4 Only 5 weeks to Morvan.... you should hurry....
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| February 22nd, 2018, 8:04 pm |
|
|
