International2cvFriends.com
http://www.international2cvfriends.com/forum/

We have liftoff.....AZU 250 rebuild thread
http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=6302
Page 15 of 19

Author:  subarupete [ September 28th, 2020, 7:09 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

Great bit of fabrication work.

Author:  Roger V [ September 28th, 2020, 7:42 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

Its amazing what you can do with a hula hoop!
Love it. :D

Author:  48pop [ September 28th, 2020, 7:58 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

Due to tight confines of the adapter, i needed to buy some M7 allen head bolts........12 quid for 5 !!!

Damn you Citroen and your M7 fetish !

Author:  Roger V [ September 28th, 2020, 8:19 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

I drilled and tapped to M8

Author:  48pop [ October 4th, 2020, 11:28 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

OK, doing a bit of a dash swap today, simple and now MPH......

I find I have a few spaces, I've seen blanks for the wee round holes, are blanks available for the rectangular holes ??

Also, I need a working wiper switch...anyone have these bits for sale?
Swap was very awkward and fiddly.......

Mostly working and I now have an oil warning light......and, no front lights.....Will get it finished over next week !

Image

Author:  Geert [ October 5th, 2020, 9:41 am ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

Ask Roger V if he can print these blanks . He owns a 3D printer as I understand

Author:  AZL57 [ October 5th, 2020, 11:08 am ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

The little lights you can take out of the other dash they are the same.
Dash is normally fixed with this type of lense shape screws.

Author:  Roger V [ October 5th, 2020, 11:42 am ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

I moved my hazard switch to the left side. The two holes at the top I use for left and right indicators. The wiper switch stayed in the bottom right corner. However, in the square hole above it, i have repurposed the brake fluid test bulb button to operate the electric windscreen washer pump.

Author:  Ianredspecial [ October 6th, 2020, 12:16 am ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

Electric washer pump?? Poshe.

Author:  48pop [ October 7th, 2020, 2:45 pm ]
Post subject:  Re: We have liftoff.....AZU 250 rebuild thread

OK, confused.......

As above, I've swapped the dash. Car starts and runs, I have tail lights, indicator and horn.....I have no front lights, nothing, no sidelights, no dipped headlights and no full beam.

I did have the lightswitch disconnected but I have checked and its all back as before.
My meter says I have 12+ volts coming to switch and when I turn the knob, 12+ volts at all other terminals (except horn)

Any thoughts on what I've missed before I tear it all out again.....?

(I had lights before the swap)

Page 15 of 19 All times are UTC + 1 hour [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/