| Author |
Message |
|
Ian
2CV Fan
Joined: March 16th, 2012, 2:41 pm
Posts: 52
|
 Gearbox mount AK350 Hi all, I thought one of the ways to try and tidy the garage was to try and put some bits on the van. Should there be a spacer or something at the mount for the old tin top gearboxes? I guess it is a lock tab that I've ended up with on the wrong side of the mount but as it is the gear lever hits the bulkhead and can't engage 1st or 3rd. It seems a long way for the engine to pull it forward. Engine not on yet.  Gearbox mount 2 on Flickr I think that the mount is the correct way round with nipples forward...  Gearbox mount on Flickr All the best. Ian
|
| May 2nd, 2018, 5:38 pm |
|
|
|
Roger V
Firing on two.
Joined: March 21st, 2013, 12:04 am
Posts: 1581
Location: Exeter, Devon
|
Re: Gearbox mount AK350 Pretty sure there are spacers on later gearboxes. Try lining up your drive shafts and see if that gives you a clue. 
_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....
|
| May 2nd, 2018, 6:01 pm |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2005
Location: South-Limburg
|
Re: Gearbox mount AK350 On my old 2cvs the flange of the body is bend down near the gear lever.
Are you sure it is a spacer and not a nut lock plate? ANd yes it should be on the other side.
|
| May 2nd, 2018, 10:00 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Gearbox mount AK350 Phew! that's a relief. 
|
| May 2nd, 2018, 10:14 pm |
|
|
|
Ian
2CV Fan
Joined: March 16th, 2012, 2:41 pm
Posts: 52
|
Re: Gearbox mount AK350 Thanks All. I think I can perform that kind of bodywork adjustment...
Indeed AZL57 it is indeed the nut lock plate that ended up on the wrong side.
|
| May 3rd, 2018, 12:17 pm |
|
|
|
Geert
Firing on two.
Joined: July 10th, 2010, 12:35 pm
Posts: 1094
Location: Magyarország
|
Re: Gearbox mount AK350 Our 1965 AZ had an "original Citroen "dent in the bulkhead to enable the gear lever move freely.
It was hard to make a new one after we replaced the bulkhead .
But now it has a copy of the "original Citroen"dent.
_________________
'T is een kwestie van geduld.........
Ez a türelem kérdése.........
|
| May 3rd, 2018, 6:21 pm |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2005
Location: South-Limburg
|
Re: Gearbox mount AK350 They had a worker at Citroen with a big hammer to make the dents... 
|
| May 3rd, 2018, 10:17 pm |
|
|
|
samfieldhouse
Firing on two.
Joined: February 11th, 2009, 12:32 am
Posts: 3324
Location: Chichester, West Sussex
|
Re: Gearbox mount AK350 Geert wrote: Our 1965 AZ had an "original Citroen "dent in the bulkhead to enable the gear lever move freely.
It was hard to make a new one after we replaced the bulkhead .
But now it has a copy of the "original Citroen"dent. Yup my van has the dent. And the 'cut and shut' gear stick.
|
| May 4th, 2018, 1:30 am |
|
|
|
Ian
2CV Fan
Joined: March 16th, 2012, 2:41 pm
Posts: 52
|
Re: Gearbox mount AK350 Would you be able to share a photo of the dent please? I think I just need to go bigger. 3rd is OK, 1st seems to be further back but I think the flange is flat there. Does it indent the actual bulkhead aswell?
|
| May 8th, 2018, 6:58 pm |
|
|
|
Geert
Firing on two.
Joined: July 10th, 2010, 12:35 pm
Posts: 1094
Location: Magyarország
|
Re: Gearbox mount AK350 I'll try to make a photo tomorrow .
_________________
'T is een kwestie van geduld.........
Ez a türelem kérdése.........
|
| May 9th, 2018, 5:22 pm |
|
|
Who is online |
Users browsing this forum: No registered users and 29 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
