|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
| Author |
Message |
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2253
Location: South-Limburg
|
 Welding thin plate I welded today on a Russian Moskvich. It's metal was even thinner than that of a 2cv... The lower chassisbar and sill were rotten through caused by a leaking 4,5 volt battery.....   https://i11.servimg.com/u/f11/18/22/17/20/dscn1110.jpg
|
| July 20th, 2017, 8:59 pm |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2253
Location: South-Limburg
|
Re: Welding thin plate This forum program does refuse my pictures very often....
|
| July 20th, 2017, 9:00 pm |
|
|
|
ken
Agony Aunt - You have a car problem? Speak to Ken
Joined: March 6th, 2009, 1:40 am
Posts: 3675
|
Re: Welding thin plate At least one reader has fallen for it... 
_________________
|
| July 21st, 2017, 1:41 am |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2253
Location: South-Limburg
|
Re: Welding thin plate it's not the stupid photobucket but the forum that said cannot determine the picture size??? I have had this more than once here? 
|
| July 21st, 2017, 6:38 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2251
Location: Near Monmouth
|
Re: Welding thin plate This forum limits images to 1mb. On windows right click to get info?
|
| July 21st, 2017, 8:03 pm |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2253
Location: South-Limburg
|
Re: Welding thin plate pic is 228 kb so that shouldn't be a problem
|
| July 21st, 2017, 9:57 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2251
Location: Near Monmouth
|
Re: Welding thin plate My 2 bytes,
It should give an error message, (in Red) if the image is to large.
Until recently, I found I had to make a few attempts to upload a picture.
For my connection a basic (3Mb) at busy times the upload failed.
I guess the host site, times-out, waiting to a response from a slow upload.
|
| July 22nd, 2017, 9:05 am |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2253
Location: South-Limburg
|
Re: Welding thin plate Ah well, stupid computers
|
| July 22nd, 2017, 3:31 pm |
|
|
|
|
Page 1 of 1
|
[ 8 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 622 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
