Oboe,
talking to Rick this morning and he mentioned something about gearboxes working better (and lasting longer) if they've got oil in them...
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Gear box input shaft , no spin http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=5532 |
Page 1 of 2 |
| Author: | oboe [ January 31st, 2015, 10:23 pm ] |
| Post subject: | Gear box input shaft , no spin |
So Slowbo Span the dummy out the other day , was driving fine then lost the clutch took engine out today and found the clutch release bearing clip had popped out on one side , fitted a new one was sorting handbrake out , before refitting engine and spinning wheels ,and saw that the shaft wasn't spinning ,tried to turn by hand ,but its rock solid can still select all gears whats going on |
|
| Author: | Sean [ January 31st, 2015, 10:44 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
what does it do in neutral? other than that dunno your going to have to open it for a look |
|
| Author: | oboe [ January 31st, 2015, 10:59 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
Gave up for the day needed a beer , the gear box had just been rebuilt be rick , hope Iv not broke it all ready |
|
| Author: | lpgo [ February 1st, 2015, 12:24 am ] |
| Post subject: | Re: Gear box input shaft , no spin |
Take a good look at the point where the inputshaft goes into the gearbox. If your bearing is pushed backwards it can melt/disform the inputshaft tube??? and block the inputshaft..... (I had this at my beamerengine).... |
|
| Author: | 2CViking [ February 1st, 2015, 11:46 am ] |
| Post subject: | Re: Gear box input shaft , no spin |
Could be buggered clutch friction plate (cracked all around) |
|
| Author: | oboe [ February 2nd, 2015, 10:32 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
Got the gearbox-guru coming to take a look and sort it out Took the lid off to have a look , will go into gears and some things turning , but no spin on the main shaft |
|
| Author: | ken [ February 3rd, 2015, 12:51 am ] |
| Post subject: | Re: Gear box input shaft , no spin |
Oboe, check the M7 bolts on the rear cover. If one of the 4 shorter ones is too long, it will foul the rearmost pinion on the mainshaft, preventing it from turning. oboe wrote: Got the gearbox-guru coming to take a look and sort it out Took the lid off to have a look , will go into gears and some things turning , but no spin on the main shaft |
|
| Author: | ken [ February 19th, 2015, 4:43 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
Oboe, talking to Rick this morning and he mentioned something about gearboxes working better (and lasting longer) if they've got oil in them...
|
|
| Author: | lpgo [ February 19th, 2015, 6:48 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
Like Ken does.. blowing to my nail Polish to dry then saying OMG and then blowing to my nail polish again... Almost dry... |
|
| Author: | oboe [ February 19th, 2015, 7:52 pm ] |
| Post subject: | Re: Gear box input shaft , no spin |
Yep I made that error  shit happens ! Il not do it again
|
|
| Page 1 of 2 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|