tin tins or rubber tins?
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Engine tinware http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=5468 |
Page 1 of 2 |
| Author: | Diesel Dave [ November 30th, 2014, 1:52 pm ] |
| Post subject: | Engine tinware |
The cylinder shrouds on my spare motor are long past their best - some buffoon even cut them to allow fitting with the manifold on situ. I can't seem to locate them on Ecas' website. Would anyone have any recommendations where I could buy some replacements? |
|
| Author: | Russell [ November 30th, 2014, 2:09 pm ] |
| Post subject: | Re: Engine tinware |
I think some of the Belgian 4x4 folk do them in polyester or similar? As for used replacements in the rubbery fibre stuff, they're almost all starting to show their age now, I have some on my current engine although I damaged them yesterday getting the manifold nuts off because I'm going to use metal shrouds. As and when I'm next at work I'll see if we have any rubber shrouds in any kind of useable condition and I'll post them to you. If you can find metal shrouds they are worth a premium and allow more engine noise to get out but can be painted nicely and dont fail like the rubber shrouds. |
|
| Author: | naughtybear [ November 30th, 2014, 7:28 pm ] |
| Post subject: | Re: Engine tinware |
I am also looking for a set of tins too! |
|
| Author: | citroenboat [ November 30th, 2014, 11:21 pm ] |
| Post subject: | Re: Engine tinware |
I have more than I need, not sure how much more, but if there any good to anyone they are in Littlehampton. |
|
| Author: | naughtybear [ December 1st, 2014, 12:36 am ] |
| Post subject: | Re: Engine tinware |
tin tins or rubber tins?
|
|
| Author: | citroenboat [ December 1st, 2014, 1:08 am ] |
| Post subject: | Re: Engine tinware |
Well I know there is a pair of cylinder 'rubbers' but I think also a pair of tins, (I need to make an engine set for myself out of the pile) maybe more. At least one spare fan housing, probably with 'Dyane turbo' tube. I will go dig in the shed in the morning & post a list. |
|
| Author: | Diesel Dave [ December 2nd, 2014, 12:26 am ] |
| Post subject: | Re: Engine tinware |
Not cheap - 130 Euro's a set! http://www.franzose.de/en/Citroen-2CV/A ... /ANR10036/ |
|
| Author: | bobh [ December 2nd, 2014, 3:21 pm ] |
| Post subject: | Re: Engine tinware |
i have a redundant set for a 425, all nicely cleaned up and painted, but I guess you want the 625s. BobH |
|
| Author: | naughtybear [ December 2nd, 2014, 3:36 pm ] |
| Post subject: | Re: Engine tinware |
yeah I am after the 602 metal ones cheers |
|
| Author: | Mark350 [ December 2nd, 2014, 5:45 pm ] |
| Post subject: | Re: Engine tinware |
bobh wrote: ...all nicely cleaned up and painted... Is this an easy DIY job; if so, what paint would you recommend? |
|
| Page 1 of 2 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|