Ash,
unless you lash out for the Burton steering column as well*, that joint won't be much use to you...
* Stainless steel and € 225,00
http://www.burtoncar.com/dms_temp/image ... 003--0.jpg
http://www.burton2cvparts.com/stuurkolo ... anguage=en
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| help with steering joint http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=5110 |
Page 1 of 2 |
| Author: | naughtybear [ December 30th, 2013, 9:39 pm ] |
| Post subject: | help with steering joint |
I bought one of these from burton..... http://www.burton2cvparts.com/swivel-jo ... -5539.html but not sure of how I am going to get the steering column to fix to it as its female both ends as you will see help please rr Ash |
|
| Author: | Pony [ December 30th, 2013, 10:47 pm ] |
| Post subject: | Re: help with steering joint |
You will probably need an adaptor i do not think the splines are 2cv Try Zx BX or Xantia steering column parts they could fit pony i |
|
| Author: | Simon Crook [ December 30th, 2013, 11:14 pm ] |
| Post subject: | Re: help with steering joint |
Hi Ash I know I have the same on my race car, I will get you a picture tomorrow so you can see what I use if that helps Simon |
|
| Author: | naughtybear [ December 30th, 2013, 11:20 pm ] |
| Post subject: | Re: help with steering joint |
that would be excellent Simon, much appreciated (starting to stress now January is just about here) and thanks also Pony |
|
| Author: | ken [ December 31st, 2013, 1:07 am ] |
| Post subject: | Re: help with steering joint |
Ash, unless you lash out for the Burton steering column as well*, that joint won't be much use to you... * Stainless steel and € 225,00 http://www.burtoncar.com/dms_temp/image ... 003--0.jpg http://www.burton2cvparts.com/stuurkolo ... anguage=en |
|
| Author: | Harley [ December 31st, 2013, 9:49 am ] |
| Post subject: | Re: help with steering joint |
I used a joint from a GS, it is a long section with a UJ at each end, you will need to cut and weld a section but it fits the spline. Harley |
|
| Author: | Simon Crook [ December 31st, 2013, 5:53 pm ] |
| Post subject: | Re: help with steering joint |
There you go Ash this is whats on mine, hope it helps |
|
| Author: | naughtybear [ January 1st, 2014, 9:24 pm ] |
| Post subject: | Re: help with steering joint |
that looks different to the joint I have, mine is approx. 4 inch long and its female at both ends, you would have thought that it would be female on the bottom end to go directly onto the rack and male top for the steering column to attach to but alas not |
|
| Author: | Little Louis [ January 1st, 2014, 9:44 pm ] |
| Post subject: | Re: help with steering joint |
Weld it at one end? |
|
| Author: | ken [ January 1st, 2014, 10:01 pm ] |
| Post subject: | Re: help with steering joint |
Ash, have you looked at the links I posted above, which show that the UJ sold by Burton is designed solely for use with their version of the steering column, which is in two pieces and has the UJ positioned about mid-way between the wheel and the pinion?  ken naughtybear wrote: that looks different to the joint I have, mine is approx. 4 inch long and its female at both ends, you would have thought that it would be female on the bottom end to go directly onto the rack and male top for the steering column to attach to but alas not |
|
| Page 1 of 2 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|