| Author |
Message |
|
Tripyrenees
Firing on two.
Joined: December 17th, 2012, 10:03 pm
Posts: 966
Location: Luscan, Pyrenees, FRANCE
|
 Brake centering tool What do you use  I need a slightly better one than the one I made up. Mine are slightly out and I want to get it right. Any pictures, links or drawings would be great Cheers Ian
_________________
https://www.facebook.com/GNGLuscan
|
| June 11th, 2013, 8:22 am |
 
|
|
|
2CViking
viking bastard
Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
|
Re: Brake centering tool Front or rear?
_________________
|
| June 11th, 2013, 8:49 am |
|
|
|
Tripyrenees
Firing on two.
Joined: December 17th, 2012, 10:03 pm
Posts: 966
Location: Luscan, Pyrenees, FRANCE
|
Re: Brake centering tool Front for starters (so there are two I need then  )
_________________
https://www.facebook.com/GNGLuscan
|
| June 11th, 2013, 3:59 pm |
|
|
|
2CViking
viking bastard
Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
|
Re: Brake centering tool Yes, original tools are hard to find. Backyarders can use this tool front and rear In short, leave the drum on. Bring the shoes out to near contact with the drum. Remove the drum without backing off the shoes (only possible without any lip on the edge) Fit the centering tool and find the highest point. Set the tool on the highest point and begin centering by turning the lower eccentrics + the back adjusting bolts if needed. Good luck Attachment: Brakes-adjuster-tool.jpg
You do not have the required permissions to view the files attached to this post.
_________________
|
| June 11th, 2013, 7:00 pm |
|
|
|
Tripyrenees
Firing on two.
Joined: December 17th, 2012, 10:03 pm
Posts: 966
Location: Luscan, Pyrenees, FRANCE
|
Re: Brake centering tool Where can I get a big bolt like that - (I have the rest to make one up)
|
| June 11th, 2013, 8:48 pm |
|
|
|
2CViking
viking bastard
Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
|
Re: Brake centering tool What bolt?
_________________
|
| June 11th, 2013, 8:53 pm |
|
|
|
Boggy
Firing on two.
Joined: October 27th, 2012, 10:45 pm
Posts: 122
Location: Deux Sevres France
|
Re: Brake centering tool A piece of 10mm rod and a couple of nuts from brico will do
Cheers
Boggy
|
| June 11th, 2013, 8:56 pm |
|
|
|
Tripyrenees
Firing on two.
Joined: December 17th, 2012, 10:03 pm
Posts: 966
Location: Luscan, Pyrenees, FRANCE
|
Re: Brake centering tool Sorry NUT!!
_________________
https://www.facebook.com/GNGLuscan
|
| June 11th, 2013, 9:32 pm |
|
|
|
ChrisW
Firing on two.
Joined: February 21st, 2012, 9:01 pm
Posts: 1136
Location: Avranches, Sud Manche, France
|
Re: Brake centering tool Thats the nut that holds on your rear hub!!
|
| June 11th, 2013, 9:55 pm |
|
|
|
bobh
Firing on two.
Joined: March 26th, 2010, 8:41 pm
Posts: 234
|
Re: Brake centering tool I made this one out of an old pipe fitting - shame to use a nice hub nut !!
You do not have the required permissions to view the files attached to this post.
|
| June 12th, 2013, 5:05 pm |
|
|
Who is online |
Users browsing this forum: No registered users and 110 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
