Just make sure you 'measure twice, cut once', as it would be a pain to correct if it was slightly off.
Also a bit of copper or brass or something helps when welding it up again, because you have to bridge the width of the cutting discs with weld.
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| RHD bulkhead panel http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=3523 |
Page 1 of 2 |
| Author: | panelbeaterpeter [ December 3rd, 2011, 1:26 pm ] |
| Post subject: | RHD bulkhead panel |
As title, is such a thing available anywhere? Computer says no. I could probably do a bit of cutting and grafting of a LHD one, but would rather not.. Thanks |
|
| Author: | ken [ December 3rd, 2011, 1:33 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Not available, however might be worth looking at George's 'cut and shuffle' of the LHD version? viewtopic.php?f=5&t=1201&start=70 ken panelbeaterpeter wrote: As title, is such a thing available anywhere? Computer says no. I could probably do a bit of cutting and grafting of a LHD one, but would rather not.. Thanks |
|
| Author: | panelbeaterpeter [ December 3rd, 2011, 1:48 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Brilliant, I couldn't picture what the side-specific section looked like, but that looks easy peasy! Will do that. Thanks Ken. |
|
| Author: | Gas Mark 5 [ December 3rd, 2011, 5:08 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Just make sure you 'measure twice, cut once', as it would be a pain to correct if it was slightly off. Also a bit of copper or brass or something helps when welding it up again, because you have to bridge the width of the cutting discs with weld. |
|
| Author: | J-dub [ December 3rd, 2011, 6:35 pm ] |
| Post subject: | Re: RHD bulkhead panel |
I thought the lower bulkhead was available? |
|
| Author: | Russell [ December 3rd, 2011, 8:05 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Lower bulkhead is but that only includes the bottom triangular box section and they're all just flat panels with none of the original fluting or detail, the complete bulkhead upto the join is available but only in lhd, doesn't take long to convert it though. |
|
| Author: | J-dub [ December 3rd, 2011, 8:46 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Ah ok I thought cassis or spoof would of sorted or been on the case 
|
|
| Author: | panelbeaterpeter [ December 3rd, 2011, 9:00 pm ] |
| Post subject: | Re: RHD bulkhead panel |
Nope, Cassis have none either. It looks very simple, will see how it goes. Might buy a few and convert them if anyone would be interested. |
|
| Author: | Geert [ December 3rd, 2011, 10:45 pm ] |
| Post subject: | Re: RHD bulkhead panel |
If this conversion does not work, you could ask 2cvKeza to make a RHD bulkhead panel for you ! I am sure he would love to help you . |
|
| Author: | J-dub [ December 4th, 2011, 8:16 am ] |
| Post subject: | Re: RHD bulkhead panel |
That's a good idea. 2cvkeza could make it in s slightly thicker material too ? |
|
| Page 1 of 2 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|