| Author | Message | 
        
			| blackjack Firing on two. 
					Joined: February 21st, 2011, 7:37 pm
 Posts: 103
   |   Width between wheel archesDoes anyone know (or perhaps could measure) the width between wheel arches on a late 80's 2CV.
 Thanks.
 
 
 | 
		
			| November 21st, 2011, 1:07 pm | 
					
					   | 
	
	
		|  | 
	
			| Bugster Firing on two. 
					Joined: August 19th, 2011, 1:24 pm
 Posts: 158
 Location: Warwickshire UK
   |   Re: Width between wheel archesNot quite sure what dimension you need bj?  But I'm at home for the day, the '88 car is sitting in a warm dry garage and I have a tape measure at the ready   
 
 | 
		
			| November 21st, 2011, 2:52 pm | 
					
					   | 
	
	
		|  | 
	
			| Sean Firing on two. 
					Joined: April 22nd, 2009, 11:06 pm
 Posts: 3684
 Location: Ecosse
   |   Re: Width between wheel archesHome for lunch today so....
 1m near as makes no difference at the crease just aft of the seat bolt (not belt  the bolt that holds the back down) housing
 _________________
 Kissing the Lash
 
  "Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
 
 
 | 
		
			| November 21st, 2011, 3:24 pm | 
					
					   | 
	
	
		|  | 
	
			| blackjack Firing on two. 
					Joined: February 21st, 2011, 7:37 pm
 Posts: 103
   |   Re: Width between wheel archesSean - thanks for doing that.  The measurement I'm after is the width between the outside walls of the rear tyres.  Not the track which is the width to the centre of the tyres.  I'd also like to know how close the tyres come to the rear wing edges.
 Thanks again.
 
 
 | 
		
			| November 21st, 2011, 6:17 pm | 
					
					   | 
	
	
		|  | 
	
			| Sean Firing on two. 
					Joined: April 22nd, 2009, 11:06 pm
 Posts: 3684
 Location: Ecosse
   |   Re: Width between wheel archesow its dark and wet now !
 wait a minute.
 
 
 44 1/2" 1130mm inner track of the wheels with 135s
 outer track 1400mm
 
 clearance to the inner wing depends on ride height.
 _________________
 Kissing the Lash
 
  "Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
 
 
 | 
		
			| November 21st, 2011, 7:05 pm | 
					
					   | 
	
	
		|  | 
	
			| blackjack Firing on two. 
					Joined: February 21st, 2011, 7:37 pm
 Posts: 103
   |   Re: Width between wheel archesYou're a star - thanks very much, much appreciated. 
 
 | 
		
			| November 21st, 2011, 9:05 pm | 
					
					   | 
	
	
		|  | 
	
			| Bugster Firing on two. 
					Joined: August 19th, 2011, 1:24 pm
 Posts: 158
 Location: Warwickshire UK
   |   Re: Width between wheel archesGuess I can put the tape away then   
 
 | 
		
			| November 21st, 2011, 11:26 pm | 
					
					   | 
	
	
		|  | 
	
			| Sean Firing on two. 
					Joined: April 22nd, 2009, 11:06 pm
 Posts: 3684
 Location: Ecosse
   |   Re: Width between wheel archesclearance to wings also dictated by the type of wing - some rep panels are so flat that you cant get the wheel out. _________________
 Kissing the Lash
 
  "Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
 
 
 | 
		
			| November 22nd, 2011, 9:18 am | 
					
					   | 
	
	
		|  | 
	
			| blackjack Firing on two. 
					Joined: February 21st, 2011, 7:37 pm
 Posts: 103
   |   Re: Width between wheel archesI'm using an untouched 1989 2CV and the wings will work like those on a DS to remove rear tyres. 
 
 | 
		
			| November 22nd, 2011, 2:05 pm | 
					
					   | 
	
	
		|  | 
	
			| Sean Firing on two. 
					Joined: April 22nd, 2009, 11:06 pm
 Posts: 3684
 Location: Ecosse
   |   Re: Width between wheel archesBugster wrote: Guess I can put the tape away then   measure random stuff and we could try to guess what it is?_________________
 Kissing the Lash
 
  "Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
 
 
 | 
		
			| November 22nd, 2011, 2:09 pm | 
					
					   | 
	
	
		|  |