I'm no mechanic by any stretch of the imagination, but I doubt single point injection would improve on a tried and tested design, stick with what you've got.
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Single point injection http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=2191 |
Page 1 of 6 |
| Author: | Justint [ September 14th, 2010, 7:12 pm ] |
| Post subject: | Single point injection |
Does anyone know if there is a single point injection kit for the 2cv? Rather than the megasquirt option. How much can you dump from the engine by doing it? ie carb etc. Thanks. |
|
| Author: | Jonathan [ September 14th, 2010, 7:24 pm ] |
| Post subject: | Re: Single point injection |
I'm no mechanic by any stretch of the imagination, but I doubt single point injection would improve on a tried and tested design, stick with what you've got.
|
|
| Author: | Little Louis [ September 14th, 2010, 7:29 pm ] |
| Post subject: | Re: Single point injection |
you could put a webber carb on but say good bye to your mpg and hello to your gpm. |
|
| Author: | Russell [ September 14th, 2010, 7:37 pm ] |
| Post subject: | Re: Single point injection |
I seem to recall that 123Ignition were developing an SPI kit, although I can't think of any off the shelf kits on the market at the moment. What are you hoping to achieve by fitting it? More power, more mpg, more reliability? |
|
| Author: | Justint [ September 14th, 2010, 7:51 pm ] |
| Post subject: | Re: Single point injection |
Better mpg I suppose, and not needing to replace a very very worn carb. I was going to go for the reconditioned carb and 123 electronic ignition, but if injection was available I would have thought about it. |
|
| Author: | Joe [ September 14th, 2010, 7:57 pm ] |
| Post subject: | Re: Single point injection |
Justint wrote: Better mpg I suppose, and not needing to replace a very very worn carb. I was going to go for the reconditioned carb and 123 electronic ignition, but if injection was available I would have thought about it. the prior would be the most cost effective, and easiest to fix if it went wrong. i would think anyway. |
|
| Author: | Neil [ September 14th, 2010, 8:28 pm ] |
| Post subject: | Re: Single point injection |
If you're serious you could have a chat with Geoff... http://www.northallerton-engineering-se ... edshop.htm http://www.2cv-speed-shop.co.uk/modifying.htm |
|
| Author: | Justint [ September 14th, 2010, 10:41 pm ] |
| Post subject: | Re: Single point injection |
Neil wrote: If you're serious you could have a chat with Geoff... Yes its possible, but starting to be a custom job really. Perhaps I will get the carb sorted and the 123 put in and wait for sometime in the future for an off the shelf injection kit when someone decides to make one. |
|
| Author: | Neil [ September 14th, 2010, 10:43 pm ] |
| Post subject: | Re: Single point injection |
ok |
|
| Author: | Tom Duckpower [ September 14th, 2010, 10:53 pm ] |
| Post subject: | Re: Single point injection |
Russell wrote: I seem to recall that 123Ignition were developing an SPI kit Correct. They named it 123/carb (what's in a name). Can't find anything about it anymore. Looks like they stopped this project, although they had one mounted on a enginge:   On their site I also can't find anything about it... |
|
| Page 1 of 6 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|