View unanswered posts | View active topics It is currently March 19th, 2024, 11:53 am



Reply to topic  [ 21 posts ]  Go to page Previous  1, 2, 3  Next
 Shock absorber fitting instruction 
Author Message
Firing on two.
User avatar

Joined: November 25th, 2010, 6:02 am
Posts: 125
Location: Adelaide, South Australia
Post Re: Shock absorber fitting instruction
Having just stuck my head under the Duck (1989), I found that the rear shocks (Lips) had been fitted back to front: they are now correctly installed, but as a 2CV newbie, can I ask why there is an "up" and a down" to these?
Is there something about the internals which requires this? :?:


November 26th, 2010, 12:42 am
Profile
Agony Aunt - You have a car problem? Speak to Ken

Joined: March 6th, 2009, 1:40 am
Posts: 3675
Post Re: Shock absorber fitting instruction
Yes,
plus the valves inside the damper body may be sensitive not only to the inclination of the damper, but also to 'which way up' the body is fitted.

If you test an A series damper, by securing one end in a vice then extending and compressing it, you should notice that as well as the usual requirement that there be no undamped movement, there should also be less effort required on 'pull' than on 'push'...

Since this is the opposite of what's required for vehicles with conventional suspension setups, it's easy to pick out those dampers where a manufacturer has simply 'adapted' a stock item to fit.

It may fit, but it won't work as it should do on an A series vehicle. :roll:

ken

_________________
Image


November 26th, 2010, 2:01 am
Profile
Firing on two.
User avatar

Joined: November 25th, 2010, 6:02 am
Posts: 125
Location: Adelaide, South Australia
Post Re: Shock absorber fitting instruction
Thanks Ken; since making the correction I think I've noticed a slight improvement in the ride, but - I'd be keen to see a cross-section of the Lips to show the internals, just the same.
Next job, I think - squirt a bit of vegetable oil into the spring cans. I'm getting a lot of road "shock" and noise transmitted through the suspension, even though the ride is soft over-all, as a 2CV should be.
God, I just love this car :D


November 26th, 2010, 8:21 am
Profile
Firing on two.

Joined: April 22nd, 2009, 11:06 pm
Posts: 3684
Location: Ecosse
Post Re: Shock absorber fitting instruction
spanner in the works time

"proper old skool boge"
Image
fit as per Workshop manual, Haynes, 2cvgb handbook, vikings post etc
newer "boge automatic or something"
Image
appear to fit the opposite way to old Boge
the blue sticker on the side says "bottom" the fitting dimple is at the top, they also seem to prefer to work with the body aligned the same as the Lip shocks above it in the photo

re badged reckords or something? has "bayonet" action plastic cover similar to Lip

Sean

_________________
Kissing the Lash
Image
"Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.


January 19th, 2011, 12:40 pm
Profile
Firing on two.
User avatar

Joined: January 26th, 2009, 10:16 pm
Posts: 1074
Location: Derbyshire
Post Re: Shock absorber fitting instruction
At registers this summer during old goats chassis change i remember the shocks getting a greasing first i think. anybody know what i saw and why?

_________________
Image
Mr Early Night aka Snuff Pusher


December 29th, 2012, 12:38 am
Profile
Firing on two.

Joined: April 22nd, 2009, 11:06 pm
Posts: 3684
Location: Ecosse
Post Re: Shock absorber fitting instruction
Rumble602 wrote:
At registers this summer during old goats chassis change i remember the shocks getting a greasing first i think. anybody know what i saw and why?


no problem with that - as the shocks get longer with use the grease protects the patrt of the rod that's exposed.

_________________
Kissing the Lash
Image
"Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.


December 29th, 2012, 12:55 am
Profile
Agony Aunt - You have a car problem? Speak to Ken

Joined: March 6th, 2009, 1:40 am
Posts: 3675
Post Re: Shock absorber fitting instruction
Aidan,
it's because the engineering chrome plating on the damper pushrods isn't as good as
it used to be, to the extent that I've seen pushrods on a set of Lipmesa dampers
develop rust pitting after just one UK winter.

When the car is jacked up to grease knife edges or carry out other servicing, that rust
pitting will damage the hydraulic seal in the damper's end cap, which will then start to
leak.

By pulling back the plastic covers and greasing the pushrods, the chances of rust
developing on the portion of the rod which isn't swept by the seal in normal use are minimised.

It's that old 'spoil the ship for a ha’pworth of tar' business, except we're talking about
grease instead of tar in this case... ;)

http://blog.ashfordchroming.com/2009/01 ... hrome.html

ken






Sean wrote:
Rumble602 wrote:
At registers this summer during old goats chassis change i remember the shocks getting a greasing first i think. anybody know what i saw and why?


no problem with that - as the shocks get longer with use the grease protects the patrt of the rod that's exposed.

_________________
Image


Last edited by ken on December 29th, 2012, 11:15 am, edited 1 time in total.



December 29th, 2012, 2:29 am
Profile
Firing on two.
User avatar

Joined: January 26th, 2009, 10:16 pm
Posts: 1074
Location: Derbyshire
Post Re: Shock absorber fitting instruction
Thanks... excellent advice ss usual.

_________________
Image
Mr Early Night aka Snuff Pusher


December 29th, 2012, 9:43 am
Profile
viking bastard
User avatar

Joined: April 18th, 2009, 11:43 am
Posts: 2424
Location: Meneac, Bretagne France
Post Re: Shock absorber fitting instruction
Except that grease and dirt makes a perfect grinding paste.

_________________
Image


December 29th, 2012, 1:07 pm
Profile WWW
Agony Aunt - You have a car problem? Speak to Ken

Joined: March 6th, 2009, 1:40 am
Posts: 3675
Post Re: Shock absorber fitting instruction
http://gabriel.com/wp-content/uploads/2 ... chmark.pdf

_________________
Image


December 29th, 2012, 7:38 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 21 posts ]  Go to page Previous  1, 2, 3  Next

Who is online

Users browsing this forum: No registered users and 22 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.