Willami wrote:
see the latest magazine - there's a good article in there.....
Dammit! I've joined the club a month too late!!
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| New windscreen surround panel http://www.international2cvfriends.com/forum/viewtopic.php?f=7&t=1497 |
Page 1 of 1 |
| Author: | Rhythm Thief [ March 21st, 2010, 8:31 pm ] |
| Post subject: | New windscreen surround panel |
My windscreen surround panel is a bit rusty, or it would be if gaffer tape was prone to rust. How much of a job is it for someone who's a reasonably competent welder to MIG one of these in? Anyone got any hints? The previous owner of the car has fibreglassed up a few holes around the screen and gaffer taped over the bonet hinge, which has all the structural rigidity of wet bread, so I think a complete panel from bonnet hinge to screen top is the best way to go. All advice appreciated. |
|
| Author: | Russell [ March 21st, 2010, 9:33 pm ] |
| Post subject: | Re: New windscreen surround panel |
Never done one, but it looks like a fanny of a job, and I understand the replacement panels are a gash fit. Wiper holes in the wrong position and holes for the electrodes too small. I'm guessing the condition of bulkhead and a panels will come into it as if they are shot you may aswell do those at the same time. Sorry I can't be any help. |
|
| Author: | Willami [ March 22nd, 2010, 3:54 pm ] |
| Post subject: | Re: New windscreen surround panel |
Rhythm Thief wrote: My windscreen surround panel is a bit rusty, or it would be if gaffer tape was prone to rust. How much of a job is it for someone who's a reasonably competent welder to MIG one of these in? Anyone got any hints? The previous owner of the car has fibreglassed up a few holes around the screen and gaffer taped over the bonet hinge, which has all the structural rigidity of wet bread, so I think a complete panel from bonnet hinge to screen top is the best way to go. All advice appreciated. see the latest magazine - there's a good article in there..... |
|
| Author: | Rhythm Thief [ March 22nd, 2010, 4:26 pm ] |
| Post subject: | Re: New windscreen surround panel |
Willami wrote: see the latest magazine - there's a good article in there..... Dammit! I've joined the club a month too late!!
|
|
| Author: | Neil [ March 22nd, 2010, 4:29 pm ] |
| Post subject: | Re: New windscreen surround panel |
Rhythm Thief wrote: Willami wrote: see the latest magazine - there's a good article in there..... Dammit! I've joined the club a month too late!! i'll try and scan the article for you tonight, unless someone can beat me to it? |
|
| Author: | Rhythm Thief [ March 22nd, 2010, 4:37 pm ] |
| Post subject: | Re: New windscreen surround panel |
Tonight should be fine ... I wasn't planning on starting it before then.  Cheers, that'd be much appreciated. |
|
| Author: | Neil [ March 22nd, 2010, 4:53 pm ] |
| Post subject: | Re: New windscreen surround panel |
Rhythm Thief wrote: Tonight should be fine ... I wasn't planning on starting it before then. 
|
|
| Author: | Neil [ March 22nd, 2010, 7:51 pm ] |
| Post subject: | Re: New windscreen surround panel |
Not really that useful, but here it is... 
|
|
| Author: | meshking [ March 22nd, 2010, 8:49 pm ] |
| Post subject: | Re: New windscreen surround panel |
I've done half of this job - I unpicked the spot welds then got a pro in to correctly mate up the new panel and weld it in. It's a long job, and chances are that you'll have rust to deal with both at the top where it meets the bodysides and where it meets the bulkhead. Also, the middle support across the inside might need replacing / fixing too. |
|
| Page 1 of 1 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|