|
Page 1 of 1
|
[ 6 posts ] |
|
Sill to floor seatbelt mounts
| Author |
Message |
|
meshking
Firing on two.
Joined: December 28th, 2008, 9:11 pm
Posts: 388
|
 Sill to floor seatbelt mounts Am I going mad, or should there be a small bracket that bolts between floor and sill on a 2cv? Just behind the b post I have the rear sill thread but also there are two threaded bolts in the floors.
Anyone put me out of my misery, please?
|
| March 7th, 2012, 9:16 pm |
|
|
|
ken
Agony Aunt - You have a car problem? Speak to Ken
Joined: March 6th, 2009, 1:40 am
Posts: 3675
|
Re: Sill to floor seatbelt mounts Hi Ben, nope, you're not losing the plot, although perhaps you've misplaced the brackets.  7/16" UNF bolt into the sill, 2 x M9 bolts through the floor into the reinforcement/captive nut carrier underneath the floor. Note that the brackets are handed. ken meshking wrote: Am I going mad, or should there be a small bracket that bolts between floor and sill on a 2cv? Just behind the b post I have the rear sill thread but also there are two threaded bolts in the floors.
Anyone put me out of my misery, please?
_________________
|
| March 7th, 2012, 9:23 pm |
|
|
|
Neil
super slot
Joined: November 28th, 2008, 11:14 pm
Posts: 8797
Location: Cornwall, UK
|
Re: Sill to floor seatbelt mounts A low quality pic of the one on the YSH: 
_________________
|
| March 7th, 2012, 9:27 pm |
|
|
|
ken
Agony Aunt - You have a car problem? Speak to Ken
Joined: March 6th, 2009, 1:40 am
Posts: 3675
|
Re: Sill to floor seatbelt mounts If you want proper low quality, (at best priiice) I can dig out a photograph where one of the M9 bolts had been replaced with an M8, held in with seam sealer on a 4k ( partial) restauration .  ken
_________________
|
| March 7th, 2012, 9:35 pm |
|
|
|
meshking
Firing on two.
Joined: December 28th, 2008, 9:11 pm
Posts: 388
|
Re: Sill to floor seatbelt mounts Argh, I've misplaced the brackets! Thanks both! I've got the bolts (for the sill) ready, just not the brackets. Seam sealer?
Anyone have a set they could send to me (in return for some cash, of course!)? Uncle Roy didn't reply (yet...)
|
| March 7th, 2012, 9:52 pm |
|
|
|
Sean
Firing on two.
Joined: April 22nd, 2009, 11:06 pm
Posts: 3684
Location: Ecosse
|
Re: Sill to floor seatbelt mounts i usually replace the M9 with M10 fine 12.9 bolts you get with the VW ball joints -but they are the wrong thread for the hubs
_________________
Kissing the Lash
"Any advice of a technical nature is given on the understanding that I've actually done this shit, not just read about it in D*lly club mag some time ago.
|
| March 7th, 2012, 10:03 pm |
|
|
|
|
Page 1 of 1
|
[ 6 posts ] |
|
Who is online |
Users browsing this forum: No registered users and 45 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
