View unanswered posts | View active topics It is currently March 28th, 2024, 5:07 pm



Reply to topic  [ 50 posts ]  Go to page Previous  1, 2, 3, 4, 5
 New with AZ 56 
Author Message
Firing on two.
User avatar

Joined: October 22nd, 2014, 10:59 pm
Posts: 1993
Location: South-Limburg
Post Re: New with AZ 56
Do you have an filter in the fuel line? I had once in france that the internals of the fuel filter desintegrated and blocked the carb.


May 17th, 2022, 4:20 pm
Profile
Firing on two.
User avatar

Joined: February 22nd, 2012, 10:34 am
Posts: 412
Location: Greece
Post Re: New with AZ 56
ΙI believe this is what Roger V is talking about.
https://citcarclubvic.org.au/wp-content ... stment.pdf

_________________
I've Been Wrong Before.


May 17th, 2022, 6:08 pm
Profile

Joined: September 27th, 2021, 7:56 pm
Posts: 23
Post Re: New with AZ 56
Many thanks for your answers and document. that i will study.

About the filter : there was none but I have installed one since.

What is bizarre is that now the engine runs perfectly with a good idling .... until the next time !

I think that i will have to clean the tank , change the rubber pipes and have the carb professionaly cleaned .

I have had the carb of my 56 AZ very well cleaned with vapour blasting by http://cbxvapourblasting.co.uk/
They are specialized in cleaning carbs for the famous CBX 6 cyl Honda bike

Best regards
MG


May 18th, 2022, 9:10 am
Profile

Joined: September 27th, 2021, 7:56 pm
Posts: 23
Post 2CV6 - Solex 26 35
Hello

Identifying the right Solex 26 35 carb repair kit on the Internet is not easy .

I understand that there are different carburettor versions with different fuel gaskets depending on the CIT codes and CSIC / SCIC codes :

- CSIC or SCIC according to mechanical or centrifugal clutch;
and :
-- CIT 197 CSIC Mechanical Clutch (1978, 2CV6 602cm3),
---CIT 198 SCIC Centrifugal Clutch (1978, 2CV6 602cm3),
---CIT 225 CSIC Mechanical Clutch (1981 to 1990, 2CV6 602cm3),
---CIT 238 CSIC Mechanical Clutch (VISA 652cm3)

For our 1987 2cv6 with mechanical clutch the CIT code should therefore be 225 .
I have not found proper documentation on the different versions of gaskets
so below is the result of my investigations .

Thanks for correcting me
MG


Attachments:
CIT 238.jpg
CIT 238.jpg [ 132.42 KiB | Viewed 12362 times ]
CIT 225.jpg
CIT 225.jpg [ 145.1 KiB | Viewed 12362 times ]
CIT 198.jpg
CIT 198.jpg [ 26.18 KiB | Viewed 12362 times ]
CIT 197.jpg
CIT 197.jpg [ 154.25 KiB | Viewed 12362 times ]
May 19th, 2022, 1:06 pm
Profile
Firing on two.
User avatar

Joined: March 21st, 2013, 12:04 am
Posts: 1577
Location: Exeter, Devon
Post Re: New with AZ 56
This may help

https://ecas2cvparts.co.uk/collections/ ... or-gaskets

_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....


May 19th, 2022, 7:28 pm
Profile

Joined: September 27th, 2021, 7:56 pm
Posts: 23
Post Re: New with AZ 56
Yes , of course ! I should have looked at Ecas.
Many thanks Roger !
MG


May 20th, 2022, 12:15 pm
Profile

Joined: September 27th, 2021, 7:56 pm
Posts: 23
Post Re: New with AZ 56
For information

The ECAS Solex refurbishment kit for 2CV6 which has been unavailable for several months has just arrived !

MG .


Attachments:
Screenshot 2022-10-03 18.30.20.png
Screenshot 2022-10-03 18.30.20.png [ 363.75 KiB | Viewed 11533 times ]
October 3rd, 2022, 7:38 pm
Profile
Firing on two.
User avatar

Joined: March 21st, 2013, 12:04 am
Posts: 1577
Location: Exeter, Devon
Post Re: New with AZ 56
that's cool :D bring it on :)

_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....


October 3rd, 2022, 10:20 pm
Profile

Joined: September 27th, 2021, 7:56 pm
Posts: 23
Post Re: New with AZ 56
Hello
My friend's 2CV6 has been running well for several months since the installation of a good fuel filter.

However the other day it refused to start because no power to the ignition
/ faulty switch under the Neiman key lock

Fortunately replacements are available from Ecas who warns " Buy this new part but please fix your water leaks to prevent failure again. "

Indeed when opening the switch, there was huge corrosion inside , apparently from winsdhield water fluid .

Note that if you open the switch , it is not possible to put it back together ( without special tools )

Thanks to Fer for his advice !

MG


Attachments:
IMG_2202.JPG
IMG_2202.JPG [ 160.22 KiB | Viewed 10603 times ]
IMG_2201.JPG
IMG_2201.JPG [ 118.81 KiB | Viewed 10603 times ]
IMG_2200.JPG
IMG_2200.JPG [ 129.37 KiB | Viewed 10603 times ]
February 25th, 2023, 7:56 pm
Profile
Firing on two.
User avatar

Joined: October 22nd, 2014, 10:59 pm
Posts: 1993
Location: South-Limburg
Post Re: New with AZ 56
You can put it together michel. It's a bit fiddly but it's possible. Put the oxydised parts in vinegar with a few spoons of salt. It will get clean. Only rinse it good afterwards.


February 26th, 2023, 6:25 pm
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 50 posts ]  Go to page Previous  1, 2, 3, 4, 5

Who is online

Users browsing this forum: No registered users and 99 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.