International2cvFriends.com
http://www.international2cvfriends.com/forum/

Yellow Dyane
http://www.international2cvfriends.com/forum/viewtopic.php?f=5&t=6250
Page 12 of 14

Author:  AZL57 [ May 1st, 2020, 10:06 pm ]
Post subject:  Re: Yellow Dyane

Some shot at it?

Author:  rob massey55 [ May 9th, 2020, 8:18 pm ]
Post subject:  Re: Yellow Dyane

I wouldn't be suprised!

ImageP1020962 by Robndaisy, on Flickr

That's the shelf in place.

ImageP1020963 by Robndaisy, on Flickr

Slots for the factory spotwelder.

ImageP1020966 by Robndaisy, on Flickr

No going back now.

ImageP1020969 by Robndaisy, on Flickr

The inner brace panel.

ImageP1020967 by Robndaisy, on Flickr

ImageP1020971 by Robndaisy, on Flickr

The side web where it fits to the gutter needs to be reduced.
I was unable to take a measurement of the gap from top to bottom of the windscreen aperture due to excessive corrosion. I'm just hoping that everything will be ok :roll: . If anyone knows what that size should be...

Author:  Roger V [ May 9th, 2020, 11:02 pm ]
Post subject:  Re: Yellow Dyane

Isn't there going to be more new car than old car!

Is that a hydrolic press I see at the back?

Author:  rob massey55 [ May 9th, 2020, 11:27 pm ]
Post subject:  Re: Yellow Dyane

:) Not as many new panels as the the van had.

The press was bought a few years ago for kingpin changing, etc. and I also used it to make the front bumper for the van. :)

Author:  Roger V [ May 9th, 2020, 11:36 pm ]
Post subject:  Re: Yellow Dyane

Well, I have press envy. :)

Do you re all where you got it?

Author:  rob massey55 [ May 10th, 2020, 8:27 am ]
Post subject:  Re: Yellow Dyane

from a garage guy up in Shropshire via eBay, £90.00 used.

Author:  rob massey55 [ May 16th, 2020, 3:26 pm ]
Post subject:  Re: Yellow Dyane

Happy day over here, thanks Ken and your man with the van, Geoff.

ImageP1020991 by Robndaisy, on Flickr

Took some carrying in by myself though, getting older.

Author:  Geert [ May 17th, 2020, 7:59 am ]
Post subject:  Re: Yellow Dyane

At times like this( a need some extra hands) I ask my wife to help me out.

Author:  rob massey55 [ May 17th, 2020, 10:36 am ]
Post subject:  Re: Yellow Dyane

Good idea! but Daisy's still in Portugal looking after her father and the neighbours are ancient. :)

Author:  rob massey55 [ May 30th, 2020, 4:30 pm ]
Post subject:  Re: Yellow Dyane

ImageP1030005 by Robndaisy, on Flickr

Got the chassis underneath to use as an alignment jig for the toeboard panels and the front footwell repair panels and generally set the bodyshell nice and even so I don't build in any more stress. I certainly don't want any more stress in my life at the moment, do you? :) .

ImageP1030006 by Robndaisy, on Flickr

Started to cut out the bad stuff. They plated both sides of the original floor pan probably to get the flamer through an MoT. Must have been great 20 years ago :lol: .

ImageP1030008 by Robndaisy, on Flickr

This toeboard is also from Ken and of course it fits perfectly :D unlike the floor repair panels. The outer will have to have the little brackets to hold the wings fitted. I'll do them later, probably much later. ;) .

Page 12 of 14 All times are UTC + 1 hour [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/