International2cvFriends.com
http://www.international2cvfriends.com/forum/

Van repairs
http://www.international2cvfriends.com/forum/viewtopic.php?f=5&t=5707		 Page 26 of 78
Author:  AZL57 [ February 6th, 2018, 7:18 pm ]
Post subject:  Re: Van repairs
It's largely exagarated. It is written in all 2cv books. I wonder if one author once had a 2cv in test with not right mounted driveshafts? And every one esle copied this story..Forks should be on the same plane otherwise they will jerk.
Author:  rob massey55 [ February 6th, 2018, 7:58 pm ]
Post subject:  Re: Van repairs
Like this then?

ImageP1010605 by Robndaisy, on Flickr
Author:  AZL57 [ February 6th, 2018, 8:56 pm ]
Post subject:  Re: Van repairs
Yes exact right... ;-)
Only bit of jerking at full turn when the car has to work heavy. Like a steep uphill sharp turn. For the rest not much different like another car..
Author:  rob massey55 [ February 6th, 2018, 9:16 pm ]
Post subject:  Re: Van repairs
Bedankt.
Author:  rob massey55 [ February 10th, 2018, 9:47 pm ]
Post subject:  Re: Van repairs
time to put the differential hub unit back together with new seals 'cos they were leaking when i stripped 'em back in 2014.

ImageP1010608 by Robndaisy, on Flickr

ImageP1010606 by Robndaisy, on Flickr

ImageP1010607 by Robndaisy, on Flickr

Had made something to undo the bushnut, found it under the bench at the back with the spiders and the mice.

ImageP1010612 by Robndaisy, on Flickr

Cleaned up the yoke for the UJ cup(because it was damaged) and partially fitted it before pressing in the shaft. Remembered to fit the brake backplate first.

ImageP1010614 by Robndaisy, on Flickr

Should have used new bearings though :roll: After trial tightening there's sideways play in the bearing so it's got to come out...somehow :) .
Author:  Geert [ February 10th, 2018, 11:08 pm ]
Post subject:  Re: Van repairs
You better replaced the bearings before putting it all together.
I don't understand why you did not replace them anyway, just in case ...
Author:  rob massey55 [ February 11th, 2018, 12:53 am ]
Post subject:  Re: Van repairs
A momentary lapse of reason :roll: :oops: :mrgreen: .
Author:  rob massey55 [ February 15th, 2018, 12:37 am ]
Post subject:  Re: Van repairs
New bearing fitted, on to the universal joint.

ImageP1010615 by Robndaisy, on Flickr

ImageP1010616 by Robndaisy, on Flickr

ImageP1010617 by Robndaisy, on Flickr

ImageP1010618 by Robndaisy, on Flickr
Author:  lpgo [ February 15th, 2018, 7:28 am ]
Post subject:  Re: Van repairs
Looking at the last picture(s) anyone from the Landrover forum would think you are doing a prop shaft..

Lovely "touchable" technics on a old 2cv..
Author:  rob massey55 [ February 18th, 2018, 7:12 pm ]
Post subject:  Re: Van repairs
Got two cups installed OK on the other shaft and then ran into trouble.

ImageP1010622 by Robndaisy, on Flickr

The cups kept misaligning and pushing the needles out of line. It took all day to get the flamer in, still the beer was nice afterwards!
Today was much easier.

ImageP1010629 by Robndaisy, on Flickr

New gaskets,

ImageP1010630 by Robndaisy, on Flickr

Making sure the adjusters are free and lubricated.

ImageP1010631 by Robndaisy, on Flickr

ImageP1010632 by Robndaisy, on Flickr

Flaming Weekend went too fast :) .
Page 26 of 78 All times are UTC + 1 hour [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/