| Author |
Message |
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2006
Location: South-Limburg
|
 Re: Van repairs It's largely exagarated. It is written in all 2cv books. I wonder if one author once had a 2cv in test with not right mounted driveshafts? And every one esle copied this story..Forks should be on the same plane otherwise they will jerk.
|
| February 6th, 2018, 7:18 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs Like this then?  P1010605 by Robndaisy, on Flickr
|
| February 6th, 2018, 7:58 pm |
|
|
|
AZL57
Firing on two.
Joined: October 22nd, 2014, 10:59 pm
Posts: 2006
Location: South-Limburg
|
Re: Van repairs Yes exact right...  Only bit of jerking at full turn when the car has to work heavy. Like a steep uphill sharp turn. For the rest not much different like another car..
|
| February 6th, 2018, 8:56 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs Bedankt.
|
| February 6th, 2018, 9:16 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs time to put the differential hub unit back together with new seals 'cos they were leaking when i stripped 'em back in 2014.  P1010608 by Robndaisy, on Flickr  P1010606 by Robndaisy, on Flickr  P1010607 by Robndaisy, on Flickr Had made something to undo the bushnut, found it under the bench at the back with the spiders and the mice.  P1010612 by Robndaisy, on Flickr Cleaned up the yoke for the UJ cup(because it was damaged) and partially fitted it before pressing in the shaft. Remembered to fit the brake backplate first.  P1010614 by Robndaisy, on Flickr Should have used new bearings though  After trial tightening there's sideways play in the bearing so it's got to come out...somehow  .
|
| February 10th, 2018, 9:47 pm |
|
|
|
Geert
Firing on two.
Joined: July 10th, 2010, 12:35 pm
Posts: 1094
Location: Magyarország
|
Re: Van repairs You better replaced the bearings before putting it all together.
I don't understand why you did not replace them anyway, just in case ...
_________________
'T is een kwestie van geduld.........
Ez a türelem kérdése.........
|
| February 10th, 2018, 11:08 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs A momentary lapse of reason   .
|
| February 11th, 2018, 12:53 am |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs New bearing fitted, on to the universal joint.  P1010615 by Robndaisy, on Flickr  P1010616 by Robndaisy, on Flickr  P1010617 by Robndaisy, on Flickr  P1010618 by Robndaisy, on Flickr
|
| February 15th, 2018, 12:37 am |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2846
Location: NL
|
Re: Van repairs Looking at the last picture(s) anyone from the Landrover forum would think you are doing a prop shaft..
Lovely "touchable" technics on a old 2cv..
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| February 15th, 2018, 7:28 am |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Van repairs Got two cups installed OK on the other shaft and then ran into trouble.  P1010622 by Robndaisy, on Flickr The cups kept misaligning and pushing the needles out of line. It took all day to get the flamer in, still the beer was nice afterwards! Today was much easier.  P1010629 by Robndaisy, on Flickr New gaskets,  P1010630 by Robndaisy, on Flickr Making sure the adjusters are free and lubricated.  P1010631 by Robndaisy, on Flickr  P1010632 by Robndaisy, on Flickr Flaming Weekend went too fast .
|
| February 18th, 2018, 7:12 pm |
|
|
Who is online |
Users browsing this forum: No registered users and 57 guests |
|
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum
|
|
