International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
The Nameless AZU http://www.international2cvfriends.com/forum/viewtopic.php?f=5&t=5424 |
Page 1 of 6 |
Author: | citroenboat [ October 15th, 2014, 7:45 pm ] |
Post subject: | Re: The Nameless AZU |
Ok, the pix came out in the wrong order but I hope they are self explanatory! The worst I can see is the bulkhead/parcel shelf, those panels are a horrendous price so I will have a go @ making or repairing them first, cab floor is just a panel & I hope most of the rest of the shell will be patching... Just the chassis & mechanicals then - piece of cake! |
Author: | Smiffy [ October 15th, 2014, 10:23 pm ] |
Post subject: | Re: The Nameless AZU |
That's the one that sat for years in a field at the lockup of ex-forum member "AZU250", isn't it? If so, it's a 1967, according to the info he gave me when I looked at it in 2010, with a view to buying. |
Author: | citroenboat [ October 15th, 2014, 10:35 pm ] |
Post subject: | Re: The Nameless AZU |
I do believe that to be the case! It has suffered from a lot of sitting around being soggy but I'm on it now |
Author: | Smiffy [ October 15th, 2014, 11:09 pm ] |
Post subject: | Re: The Nameless AZU |
As I remember it, there were some staggeringly solid and in-tact parts to that van... but also some extremely sieve-like rusty bits. It scared me off, but I mourned not buying it for weeks! I really coveted it, and look forward to seeing you get it back up to scratch! Good luck. It'll be worth it! Oh, and here are some pics I took of your van when I was lusting over it!! |
Author: | Russell [ October 15th, 2014, 11:17 pm ] |
Post subject: | Re: The Nameless AZU |
I nearly went for that when it looked much like in those pictures. Maybe I should have, although it doesn't seem to have done very well in the intervening years. Hope to see it puttering round in the near future. |
Author: | citroenboat [ October 16th, 2014, 11:37 am ] |
Post subject: | Re: The Nameless AZU |
Crackin' pix Smiffy! Thanks Interestingly the middle body crossmember on the right (supports rear of petrol tank) appears straight in the photie - it's now bent backwards about 15mm @ it's outer end. The bulkhead already looks like it had gone thru in places... |
Author: | citroenboat [ October 18th, 2014, 12:12 pm ] |
Post subject: | Re: The Nameless AZU |
Spent money now Wonderful Uncle Roy is speeding rear wings, back door hinges, body side rails, floor, etc. in my direction. However, replacement for the rotten upper bulkhead is not available, so I have either to repair the existing one (a strip about 6" wide across the middle) or make a complete one. Making one would be most satisfying & a better repair I think, but I've not done any thin sheet metal stuff like this before, any thoughts, tips, ideas please? I'm thinking the bulkhead should be 0.75mm thick? At the mo I'm thinking of a 'buck' made of 3mm steel plate (because I have some) with 'ribs' of 5 x 25mm flat bar welded to it corresponding with the edges of the pressed ribs, thus forming slots that a hard wood or steel round bar of the same dia as the width of the ribs could be belted into to form the ribs in the bulkhead. Studding welded to the 3mm where there are holes in the bulkhead could be used to clamp the thin stuff to the buck... Vent tubes, gearshift stabaliser mount, etc. transfered across & there is an oval pressing in the top l/h corner of the existing panel that I think I shall have to cut out and weld onto the new one as I doubt I can whack that in satisfactorily... |
Author: | subarupete [ October 18th, 2014, 12:56 pm ] |
Post subject: | Re: The Nameless AZU |
Making the buck (former) sounds like a task in its self, but as you say statisfying. Maybe look up 2cvzeka on this forum for ideas. |
Author: | Geert [ October 18th, 2014, 3:40 pm ] |
Post subject: | Re: The Nameless AZU |
We have the same problem with the bulkhead of our 1965 2CV AZ, still not sure how to deal with it. We might patch it up with parts of a newer type 2CV bulkhead. https://flic.kr/p/hTKZwZ |
Page 1 of 6 | All times are UTC + 1 hour [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |