Bugger!
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| 1976 AZU250 http://www.international2cvfriends.com/forum/viewtopic.php?f=5&t=3554 |
Page 36 of 42 |
| Author: | Smiffy [ April 4th, 2015, 2:41 pm ] |
| Post subject: | Re: 1976 AZU250 |
Bugger!
|
|
| Author: | banjo [ April 4th, 2015, 7:18 pm ] |
| Post subject: | Re: 1976 AZU250 |
Oops maybe a little heat on the alloy post and a squirt of pipe freeze on the stud should see it out. 
|
|
| Author: | Smiffy [ April 5th, 2015, 6:24 pm ] |
| Post subject: | Re: 1976 AZU250 |
 Approaching the level of cheap farce now. Think I'll take it to an engine shop and see if they can help.
|
|
| Author: | Russell [ April 5th, 2015, 7:13 pm ] |
| Post subject: | Re: 1976 AZU250 |
I can post you another head. Seriously, that stud isn't coming out. |
|
| Author: | Smiffy [ April 5th, 2015, 11:28 pm ] |
| Post subject: | Re: 1976 AZU250 |
Also set about rebuilding my suspension cans today. Noticed that there was a bit missing from one of my spring end cups:  Can this be repaired, or should I bite the bullet and buy a new one? Does anyone have a spare that I could swap for beer tokens of sommat? |
|
| Author: | Geert [ April 6th, 2015, 7:46 am ] |
| Post subject: | Re: 1976 AZU250 |
You could buy a new one, not that expensive : http://www.ecas2cvparts.co.uk/lined-spr ... -1192.html For that stud: find an engine shop , they' ll have it out in no time. |
|
| Author: | Smiffy [ April 6th, 2015, 6:09 pm ] |
| Post subject: | Re: 1976 AZU250 |
Calling all metal gurus! Does anyone on here have the metal bending skills/equipment to fabricate one or two of these (one for each side of the vehicle) for me?  This image of the severely bashed original shows that each single piece needs to be bent in two places, along its entire length.  If there isn't anyone on here who can help, does anyone know anyone who could help? This pic shows where the piece comes from, at the front edge of the rear wing: 
|
|
| Author: | Russell [ April 6th, 2015, 8:50 pm ] |
| Post subject: | Re: 1976 AZU250 |
Can you send me a fairly accurate drawing of it? Mainly the profile and the length. Should be no issues to make. |
|
| Author: | Smiffy [ April 7th, 2015, 2:46 pm ] |
| Post subject: | Re: 1976 AZU250 |
This is the plan and photos for the nearside, ie left-hand side of the car. Click to enlarge the first image. Hope it's clear and detailed enough. Attachment: AZU nearside rear front edge.jpg [ 40.15 KiB | Viewed 5235 times ]   (note: very deformed! Originally nice and precise and machined.)  Underside   Please let me know if you need any further info, photos etc. |
|
| Author: | Smiffy [ May 25th, 2015, 11:28 pm ] |
| Post subject: | Re: 1976 AZU250 |
Original suspension can tube end:  Replacement tube end:  Felt seal thingy for tube end:  Doesn't fit right:  Am I doing something wrong? What should I be doing to get it fitting correctly? |
|
| Page 36 of 42 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|