View unanswered posts | View active topics It is currently March 29th, 2024, 4:25 pm



Reply to topic  [ 86 posts ]  Go to page Previous  1, 2, 3, 4, 5 ... 9  Next
 Lars E' 0,6Tii 2cv special 
Author Message
Firing on two.
User avatar

Joined: January 5th, 2009, 5:48 am
Posts: 1687
Location: Haven't a clue
Post Re: Lars E' 0,6Tii 2cv special
This is very interesting Lars. Do you still have a 2cv gearbox? How does it survive with 73Nm of torque? Or have you changed it for a GS type?

_________________
Image


April 26th, 2010, 11:05 pm
Profile
Firing on two.
User avatar

Joined: September 6th, 2009, 12:56 am
Posts: 467
Location: Oxfordshire
Post Re: Lars E' 0,6Tii 2cv special
Interesting wipers too - I've never seen them like that on a 2cv before, have you done something clever with the linkages or is it a custom design?

_________________
Image


April 26th, 2010, 11:21 pm
Profile
Firing on two.
User avatar

Joined: April 17th, 2009, 8:30 pm
Posts: 111
Location: Aale city, denmark
Post Re: Lars E' 0,6Tii 2cv special
Gearbox ... No, I no longer ride with a 2CV gearbox, I run on a Dyane gearbox. But I have over the winter built a new one, of fragments from a AMI8, Dyane and 2CV. I could use the larger 4th gear is in a Dyan gerkasse, but was tired of the low first gears, and the larger jumps between gearne. So now I have the same distance between gears in a 2CV gearbox, but they are higher than in both Dyane and Ami.

Window-wipers ... Well .. they just moved so they are symmetrical. and then the left arm "turned" upside down so that it points upwards, it means that they move in opposite directions. If it be copied, they must be installed approximately 2cm farther apart than I did when my arms just touch each other

_________________
Image 2cv special 0,6Tii
viewtopic.php?f=5&t=1610
http://snail.s4.bizhat.com/viewtopic.ph ... orum=snail


April 27th, 2010, 7:34 am
Profile WWW
Firing on two.
User avatar

Joined: April 17th, 2009, 8:30 pm
Posts: 111
Location: Aale city, denmark
Post Re: Lars E' 0,6Tii 2cv special
Hey, there's little new from the workshop, it has not been made so much the past few months, because I had surgery in the clavicle, and to not use my right arm.

But now the springs and suspension when finally installed. Galvanic chassis frame, stainless springs, boxes and mounting tubes. The hardest springs I could find in the box (around 20-25% stronger). Shocks in the rear with the gear oil, new shock absorbers in the front (they also have changed the oil for gear oil) Rubber interaction has been removed and replaced with aluminum cones (as in an Acadian).
It will be exciting to get out and run.

Image

Image

Image
Fuel pump and filter

Image
The suction tube into the fuel tank is 12mm.

_________________
Image 2cv special 0,6Tii
viewtopic.php?f=5&t=1610
http://snail.s4.bizhat.com/viewtopic.ph ... orum=snail


May 21st, 2010, 10:00 am
Profile WWW
Firing on two.
User avatar

Joined: April 17th, 2009, 8:30 pm
Posts: 111
Location: Aale city, denmark
Post Re: Lars E' 0,6Tii 2cv special
So, I've been in workshop again, is in the process of constructing an a new set of rear wheels.
Everything is easy with an angle grinder :-)
Now they just get past the sandblasters and powder coated so they are ready

Image

Image

Image

Image

Image

_________________
Image 2cv special 0,6Tii
viewtopic.php?f=5&t=1610
http://snail.s4.bizhat.com/viewtopic.ph ... orum=snail


February 9th, 2011, 9:33 pm
Profile WWW
Firing on two.
User avatar

Joined: April 17th, 2009, 8:30 pm
Posts: 111
Location: Aale city, denmark
Post Re: Lars E' 0,6Tii 2cv special
So is The bodies and wheels come back from the blaster, lucky not so much rust as I had feared.
Little in the right panel, and gutter at A pillars, so it's just to get started, so I get to the fun. (modification)
rear wheels were finished today, and they get along with reserved and front rims sent for powder coating on Monday.
Front tires came with GLS here today from daekonline.dk. 135/70 * 15

Image

Image

Image

Image

Image

And then some other pictures of a disassembled 2CV

Image
fuel return
Image
12mm suction pipe
Image
Pump and filter
Image

Image

Image

Image

Image
.

_________________
Image 2cv special 0,6Tii
viewtopic.php?f=5&t=1610
http://snail.s4.bizhat.com/viewtopic.ph ... orum=snail


February 24th, 2011, 10:44 pm
Profile WWW
Firing on two.
User avatar

Joined: October 7th, 2009, 12:10 pm
Posts: 2192
Location: NWUK
Post Re: Lars E' 0,6Tii 2cv special
Amazing!

_________________
Image
'Democracy my Arse'


February 24th, 2011, 10:50 pm
Profile WWW
Beard
User avatar

Joined: December 9th, 2008, 8:00 pm
Posts: 2003
Post Re: Lars E' 0,6Tii 2cv special
Wierd, I was lying in bed last night thinking... ''I wonder if Lars has progressed with his car''

And... tadaaa heres an update. Nice work.

_________________
.
Image
.

http://www.rollingonfour.co.uk


February 25th, 2011, 1:42 am
Profile
Firing on two.

Joined: July 26th, 2009, 3:36 pm
Posts: 1019
Post Re: Lars E' 0,6Tii 2cv special
Blimey, that's a bit impressive... :shock:

You've lost me with what you've done with the wheels, tho', Lars. Or rather, I can see what you've done, but don't know why :?
Lars E wrote:

Image


The finished wheel on the right doesn't look any wider than the one on the left - is it to change the offset that all that work was done?

And then you say you're going to fit 135/70s - tyres no wider than usual...

I'm confused :oops:


February 25th, 2011, 11:53 am
Profile
Firing on two.
User avatar

Joined: April 17th, 2009, 8:30 pm
Posts: 111
Location: Aale city, denmark
Post Re: Lars E' 0,6Tii 2cv special
It's rear wheels I have built. I started with a set of 4.5 "GSA rims where I've cut the outer ring of, to mount the inner ring of a set of 6" Xsara rims to create a set of 5.25 "wide GSA rims for my 2CV.
They will be fitted with either 145/80 or 155/70 * 15 * 15 tires.

The other tires will be mounted on standard GSA rims in front.

_________________
Image 2cv special 0,6Tii
viewtopic.php?f=5&t=1610
http://snail.s4.bizhat.com/viewtopic.ph ... orum=snail


February 26th, 2011, 10:29 am
Profile WWW
Display posts from previous:  Sort by  
Reply to topic   [ 86 posts ]  Go to page Previous  1, 2, 3, 4, 5 ... 9  Next

Who is online

Users browsing this forum: No registered users and 156 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.