| Author |
Message |
|
Smiffy
Firing on two.
Joined: October 23rd, 2009, 10:41 pm
Posts: 2356
Location: Worcestershire
|
 Re: Sudo Kubel twofifty AZU wrote: Smiffy wrote: Just realised I know only marginally more than f***all about bodywork, so I will google "swaging machine", "b read roller" and "brake press" when I get home.  Bead roller will give better results .......  Unless you're hungry of course  Actually, I was hungry at the time I posted. Freudian!
_________________
|
| October 26th, 2010, 2:44 pm |
|
|
|
Tony England
2CV Fan
Joined: April 10th, 2009, 2:54 am
Posts: 62
Location: Maldon, Essex
|
Re: Sudo Kubel Hey Smiffy, as its a german replica, ive got a 'bread' bag if thats any help
|
| October 26th, 2010, 11:35 pm |
|
|
|
Smiffy
Firing on two.
Joined: October 23rd, 2009, 10:41 pm
Posts: 2356
Location: Worcestershire
|
Re: Sudo Kubel Tony England wrote: Hey Smiffy, as its a german replica, ive got a 'bread' bag if thats any help Right now, I getting a feeling I haven't had since school: you know, the one where you haven't got an effin' clue what's being said by the bigger, cooler lads who know what's what, so you go along with it cos you think it's right... and then all the cool kids laugh at you cos you shouldn't have gone along with it... so I'm going to say NOTHING!
_________________
|
| October 27th, 2010, 12:04 am |
|
|
|
Jonathan
Firing on two.
Joined: January 1st, 2009, 7:37 pm
Posts: 4708
Location: Disunited Kingdom
|
Re: Sudo Kubel
_________________
1988 built (1989 F-registered) Citroën 2CV-Six
2013 (63-Plate) VW Golf SE 1.4TSI BMT DSG7
1932 Morris Minor Open Two-Seater (The £100 car).
|
| October 27th, 2010, 12:13 am |
|
|
|
Tony England
2CV Fan
Joined: April 10th, 2009, 2:54 am
Posts: 62
Location: Maldon, Essex
|
Re: Sudo Kubel
|
| October 28th, 2010, 12:05 am |
|
|
|
Smiffy
Firing on two.
Joined: October 23rd, 2009, 10:41 pm
Posts: 2356
Location: Worcestershire
|
Re: Sudo Kubel
_________________
|
| October 28th, 2010, 10:42 am |
|
|
|
Tony England
2CV Fan
Joined: April 10th, 2009, 2:54 am
Posts: 62
Location: Maldon, Essex
|
Re: Sudo Kubel Welded on the spare wheel mounting. Needed a nice round shape and ended up with a stainless steel mixing bowl  Does the job tho and gives me enough room underneath for the K&N filter.   Welded a stud on the top after, which sticks through the centre of the wheel and hold it on with a nut and washer.  Done some more on the rear end but the camera batteries went flat. Photos next time.
|
| November 2nd, 2010, 12:07 am |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2847
Location: NL
|
Re: Sudo Kubel is there realy enough space between the stainless steel mixing bowl and your air-intake rubber.... when you start your car or when you go from zero to full throttle your engine shakes a lot, try this first before you weld everything together........
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| November 2nd, 2010, 7:44 am |
|
|
|
Rusty
Firing on two.
Joined: January 12th, 2010, 10:33 am
Posts: 193
Location: Koudekerk ad Rijn, Netherlands
|
Re: Sudo Kubel lpgo wrote: is there realy enough space between the stainless steel mixing bowl and your air-intake rubber.... when you start your car or when you go from zero to full throttle your engine shakes a lot, try this first before you weld everything together........ I was thinking the same  other than that, nice job again! greetzzzzzzzzzzzzzz
_________________
bitten by the Citobug...
|
| November 2nd, 2010, 9:42 am |
|
|
|
Tony England
2CV Fan
Joined: April 10th, 2009, 2:54 am
Posts: 62
Location: Maldon, Essex
|
Re: Sudo Kubel Good point guys. The actual clearance is a little more than these photos as it was re positioned just before it was welded on, but i will check it tho. Thanks .
|
| November 3rd, 2010, 1:56 am |
|
|
