International2cvFriends.com :: View topic

Pony wrote:

For the rear
i can offer you an open choice
Straight
curved ends
with a mix of hoops or the over rider like the sahara
Roy ECAS in the UK has a stock of the most common ones
but if you like a special one made up it would not be a problem,
as i have all the jigs tubes and mounts in stock

Pony wrote:

For the rear
i can offer you an open choice
Straight
curved ends
with a mix of hoops or the over rider like the sahara

Pony wrote:

re rear bumper for AZU van / AK van
tubing 35 mm dia with a 2 mm wall thickness
all possible , the mounting plates could accomodate
an additional upright bracket to allow it to sit under that rear member
only i would need to know what height you would like it to sit at and what length?
do you go to Poland as it could be a chance to make a basic drawing idea of mounting etc?
or send me a sketch of your requirements.
i will take some stock with me
pony

Trevorwat wrote:

Any of the front ones made it to the UK yet for sale?

Author:	chevrons2 [ June 19th, 2015, 11:19 am ]
Post subject:	Re: PO Bumpers for Vans
Pony wrote: For the rear i can offer you an open choice Straight curved ends with a mix of hoops or the over rider like the sahara Roy ECAS in the UK has a stock of the most common ones but if you like a special one made up it would not be a problem, as i have all the jigs tubes and mounts in stock I've looked at the ones on Roy's website. Can you do a rear one for AK/AZU?: The mounting brackets would need to be stepped somehow, (because the rear panel is lower than the chassis).

Author:	Robcap [ June 19th, 2015, 7:38 pm ]
Post subject:	Re: PO Bumpers for Vans
Pony wrote: For the rear i can offer you an open choice Straight curved ends with a mix of hoops or the over rider like the sahara For the rear I would like to have a straight one, just as wide as the rear body. Same diameter as the front one. I'll send you a PM. Cheers, Rob

Author:	Pony [ June 19th, 2015, 9:21 pm ]
Post subject:	Re: PO Bumpers for Vans
re rear bumper for AZU van / AK van tubing 35 mm dia with a 2 mm wall thickness all possible , the mounting plates could accomodate an additional upright bracket to allow it to sit under that rear member only i would need to know what height you would like it to sit at and what length? do you go to Poland as it could be a chance to make a basic drawing idea of mounting etc? or send me a sketch of your requirements. i will take some stock with me pony

Author:	samfieldhouse [ July 2nd, 2015, 12:22 pm ]
Post subject:	Re: PO Bumpers for Vans
Pony wrote: re rear bumper for AZU van / AK van tubing 35 mm dia with a 2 mm wall thickness all possible , the mounting plates could accomodate an additional upright bracket to allow it to sit under that rear member only i would need to know what height you would like it to sit at and what length? do you go to Poland as it could be a chance to make a basic drawing idea of mounting etc? or send me a sketch of your requirements. i will take some stock with me pony I too would be interested in this as the rest of an AK/AZU is quite exposed. I'll be in Poland with my 350, happy for it to be measured

Author:	Dennis [ July 2nd, 2015, 6:29 pm ]
Post subject:	Re: PO Bumpers for Vans
I'd be interested in front and rear for my AZU 250. Unfortunately although I will be in Poland, it won't, and the rear of a 250 must be different from a 350. Currently it has an angle-iron bar ("C" section) bolted to the two loops below the door. I think these were standard PTT fittings, but no doubt someone better informed can put me right. And I'd love to replace the badly decayed "paperclip" overriders I already have.

International2cvFriends.com http://www.international2cvfriends.com/forum/

PO Bumpers for Vans http://www.international2cvfriends.com/forum/viewtopic.php?f=4&t=5657	Page 2 of 3

Author:	Pony [ July 2nd, 2015, 10:04 pm ]
Post subject:	Re: PO Bumpers for Vans
Re 250 van rear C section bumpers I think this C section was fitted By the Belgian post office to do a better job protecting the rear end, as i remember importing s few 3 window AZU 250 vans in the eighties! I have a 400 van in my yard so will do a bit of checking as to what would be the best route for mounting etc. but get your thinking cap on as to what you like and i will bring a few bumpers for local sale in Poland

Author:	Trevorwat [ August 8th, 2015, 10:21 pm ]
Post subject:	Re: PO Bumpers for Vans
Any of the front ones made it to the UK yet for sale?

Author:	Roy Eastwood [ August 10th, 2015, 8:58 am ]
Post subject:	Re: PO Bumpers for Vans
http://www.ecas2cvparts.co.uk/tubular-front-bumper-faithfull-copy-citroens-classic-bumper-used-some-vans-2cvs-destined-road-p-2267.html Trevorwat wrote: Any of the front ones made it to the UK yet for sale?

Author:	Trevorwat [ August 10th, 2015, 3:10 pm ]
Post subject:	Re: PO Bumpers for Vans
Thanks Roy! It wasn't on the website when I last looked (or I missed it!)

Page 2 of 3	All times are UTC + 1 hour [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/