View unanswered posts | View active topics It is currently April 25th, 2024, 7:34 am



Reply to topic  [ 3975 posts ]  Go to page Previous  1 ... 346, 347, 348, 349, 350, 351, 352 ... 398  Next
 What did you do with your A Series today? 
Author Message
Firing on two.
User avatar

Joined: October 5th, 2009, 8:22 pm
Posts: 1415
Location: Stone, Staffs
Post Re: What did you do with your A Series today?
TBH - its had slightly, around 50mm, lowered front suspension since I bought it 4/5 years ago, doesnt ground, handles fine, tracking is OK, and goes to Richard Dalton every year for MOT and never had this before....

_________________
1987 2CV Special
2014 Suzuki Swift Sport
2015 Lexus NX300h
1966 Ami Break


February 2nd, 2017, 12:02 am
Profile
Firing on two.

Joined: April 9th, 2010, 12:21 am
Posts: 464
Location: West Sussex
Post Re: What did you do with your A Series today?
Nelsthebass wrote:
........slightly, around 50mm, lowered front suspension........

In that case, I'm surprised he noticed!


February 2nd, 2017, 1:56 pm
Profile WWW
Firing on two.

Joined: June 22nd, 2014, 8:09 pm
Posts: 1180
Location: Reading, Berks UK
Post Re: What did you do with your A Series today?
Me too, most people have no idea about the 2cv & they often need explaining at MOT don't they.


February 2nd, 2017, 2:10 pm
Profile
Firing on two.
User avatar

Joined: January 1st, 2009, 7:37 pm
Posts: 4696
Location: Disunited Kingdom
Post Re: What did you do with your A Series today?
Deuche has been sat in the garage for over a week, due to work and bad weather. Today the weather was rather decent, so I decided to use it to commute* to work this morning. Couple of attempts resulted in a flat battery, so I used the Golf instead. On returning home this evening I hooked up the jump leads, started the 2CV, and shot off down to the ferry terminal and back. Was nice to see a degree of daylight still in the western sky at 5pm. Just a couple of weeks ago it was dark a little after 3pm! Give it another few weeks and I'll be able to spend some time on the Morris in the evenings. Still need to send off for a rebuild kit for the OM Series SU carburettor.

*I say 'commute' but it's only four miles away and I generally pass two cars and a Post Office van going the other way, so not much of a journey. :lol:

_________________
1988 built (1989 F-registered) Citroën 2CV-Six
2013 (63-Plate) VW Golf SE 1.4TSI BMT DSG7
1932 Morris Minor Open Two-Seater (The £100 car).
Image
Image


February 4th, 2017, 1:05 am
Profile
Firing on 1-2 Spark
User avatar

Joined: November 8th, 2009, 5:42 pm
Posts: 2846
Location: NL
Post Re: What did you do with your A Series today?
collected a free sofa for the livingroom
Attachment:
IMG-20170205-WA0001.jpg
IMG-20170205-WA0001.jpg [ 256.08 KiB | Viewed 3274 times ]

_________________
Russell wrote:
Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ


Last edited by lpgo on February 5th, 2017, 12:58 pm, edited 1 time in total.



February 5th, 2017, 12:42 pm
Profile WWW
Firing on two.
User avatar

Joined: March 21st, 2013, 12:04 am
Posts: 1581
Location: Exeter, Devon
Post Re: What did you do with your A Series today?
:lol:

_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....


February 5th, 2017, 12:46 pm
Profile
2CV Fan

Joined: December 6th, 2015, 12:09 am
Posts: 46
Post Re: What did you do with your A Series today?
.
not what I've done today, but this past week..

I've been replacing the steel rear wings on Sami, my Ami-S, with grp panels. The original (1974) panel although dented and with minor rust is perfectly restorable., but I didn't want to cut and shove it.. and yet I wanted to change the design slightly - to have a rear arch cutout, not dissimilar to that seen on the M35.

Not only do I feel this helps visually balance out the car a little better, but it should also help when changing the rear wheel.

Because the standard arches are so low and closely tucked under, this involves jacking the car wwaaayyy up in the air - until the wheel drops down sufficiently to get the dished wheel clear of the brake hub & its studs. And if you don't want to scratch all the paint off the inside of the wheel, then you have to crawl under the car to see what you are doing :o

The lack of lateral clearance means the Ami is even worse than either the 2cv or Dyane. And in the event of a roadside puncture (or in a field car-park as I had last year) where the ground is neither level nor firm - then jacking the car up so high is (imo) an unnecessary risk. So, it was either a case of making a removable spat, or a cut-out arch. Personally I prefer the M35 look.., which also happens to be the easier option ;)

Attachment:
P1230504s.jpg
P1230504s.jpg [ 129.75 KiB | Viewed 3228 times ]
^ Sami ..as was. The original wheels had been rubbed down and repainted over the previous week.

Attachment:
P1230561.jpg
P1230561.jpg [ 95.49 KiB | Viewed 3228 times ]
^ old grp wing acquired, trial fitted & marked, cutout shape defined and cut out. You can get an idea of how flat that panel was in way of the wheelarch out out. And it was like this before I cut it.

Attachment:
P1230568.jpg
P1230568.jpg [ 100.61 KiB | Viewed 3228 times ]
^ first look ..am pleased :)

Attachment:
P1230580s.jpg
P1230580s.jpg [ 127.07 KiB | Viewed 3228 times ]
^ most of the previous paint and filler removed (hand scraped as you can't use chemical or blasting with grp). Then I trial fitted the rear light, dug out air bubbles (..from crappy manufacturing quality), refined the panel to body fit, and assessed the general shape (grp panels have a habit of flattening out if not stored properly whilst fully curing). I then set about fitting a bowed batten to correct and hold the panel's shape. NB. The original steel panel has a similar reinforcement running parallel with it's bottom edge.

Attachment:
P1230604.jpg
P1230604.jpg [ 110.01 KiB | Viewed 3228 times ]
^ batten bonded in place and glassed over. Also the panel's front edge return (the rear door shut) was extended inwards from being a meager 8-10mm to 25 - 30mm. And the panel fastening tab (which had been ripped off) was rebuilt.

Attachment:
Ami Super P1230615s.jpg
Ami Super P1230615s.jpg [ 121.92 KiB | Viewed 3228 times ]
^ the curve (panel shape) now continues as a smoother line from rear door to the rear lamp. It was almost flat where the wheelarch now is (..even before I cut it).

Attachment:
P1230616s.jpg
P1230616s.jpg [ 96.52 KiB | Viewed 3228 times ]
^ much better wheel removal clearance and line 8-) But the shadow lines (edges of the relief) had been rounded off too much (not by me !). Body workers with da in hand forget the fibreglass is not steel ! - it's only as hard as body filler., so the defined edges tend to get lost.

Attachment:
P1230621s.jpg
P1230621s.jpg [ 83.86 KiB | Viewed 3228 times ]
^ panel shape / shadow lines being redefined (work in progress) before final finishing and paint. It's already much better shape than the original panel.., and so I'm hoping it'll look good when done.

Attachment:
P1230586.jpg
P1230586.jpg [ 76.03 KiB | Viewed 3228 times ]
^ And of course while access was good - I repainted the inner wheel arch / body.



February 13th, 2017, 1:24 pm
Profile
Firing on two.
User avatar

Joined: March 21st, 2013, 12:04 am
Posts: 1581
Location: Exeter, Devon
Post Re: What did you do with your A Series today?
Looking good 2CY :)

Today, hopefully, I have cured a bad oil leak by changing the oil cooler seals.

ps

Thanks Roy @ Ecas for a brilliant postal service. :D

_________________
If you can't fix it with a hammer, it's probably electrical (or, an electric fuel pump!) ....


February 13th, 2017, 6:00 pm
Profile
Firing on two.

Joined: February 17th, 2009, 8:43 pm
Posts: 567
Location: NOrWAY
Post Re: What did you do with your A Series today?
Great work 2CY! I like the attention to details like the shape of the curve, and the work you put in to it.

I even think I like the look. Would be nice with a picture of the whole car from the side when work is finished.

_________________
Vennlig hilsen, Eirik
Image
Five 2CV's, DS 21 ieh Pallas -70, DS 23 h Pallas -75, CX 25 GTi automatic -89, XM 2,0i -90
And a Heinemann Z412 -80


February 13th, 2017, 10:58 pm
Profile
2CV Fan

Joined: December 6th, 2015, 12:09 am
Posts: 46
Post Re: What did you do with your A Series today?
.
Thank you Roger & Eirik for your kindly encouragement.

I'll do my best to provide a picture of the rear side quarter - once it's in white primer and with the rear lamp fitted ..later this week. ;)

Below is the front view taken on Friday. Those who know the Ami will immediately note that I've removed the (imo) ugly black rubber overriders and the excessively heavy (visually) number plate mounting.

I'm hoping to fit a period 'black on polished aluminium' number plate to the lower valance panel, but already it looks to me a very much lighter style.

Attachment:
Ami Super P1230611s.jpg
Ami Super P1230611s.jpg [ 119.94 KiB | Viewed 3194 times ]

The rear bumper's rubber overriders have likewise also now been removed. These cars are really quite small., and so 'clutter' like that only detracts from an actually ..not so ugly duckling.

I would like to try a pair of clear/white front indicators, rather than the amber ones - If anyone happens to be kind enough to donate to the cause. The rear lights 'chrome' surrounds have also yellowed badly if anyone has some with shiny (silver coloured) chrome. ;)


February 14th, 2017, 1:41 am
Profile
Display posts from previous:  Sort by  
Reply to topic   [ 3975 posts ]  Go to page Previous  1 ... 346, 347, 348, 349, 350, 351, 352 ... 398  Next

Who is online

Users browsing this forum: No registered users and 161 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group.
Designed by STSoftware for PTF.