| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| any one know anything about dyane's? and some parts? http://www.international2cvfriends.com/forum/viewtopic.php?f=4&t=3503 |
Page 1 of 2 |
| Author: | dyane72 [ November 25th, 2011, 11:02 pm ] |
| Post subject: | any one know anything about dyane's? and some parts? |
Hi all, i have a 72 Dyane and some of the parts im not sure about, it came with 2 starter handles, one with a metal coil around the handle and one without. anyone know why this is?? also had some metal foot plates (this is what they look like) i think they are stainless as had rust works on them but all came off with wire wool and shines up nice, can any one tell me what they are? Regards, Adam. |
|
| Author: | ken [ November 25th, 2011, 11:17 pm ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
Adam, the starting handle with the coil is probably the older (and better) version, they certainly seem easier to use.  Those stainless parts are screwed onto the inner face of the sills and are intended to protect the joins in the door seals from being caught by the driver's or passengers' feet, I think. ken |
|
| Author: | dyane72 [ November 26th, 2011, 12:09 am ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
that all makes sense, thank you!!! Adam |
|
| Author: | Sean [ November 26th, 2011, 10:28 am ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
yup stainless and there to stop the seal being knocked off the flange every time you get out |
|
| Author: | Jacqueslemac [ November 27th, 2011, 5:18 pm ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
At one time I had a 1969 Dyane and one from 1982. It was amazing how many things had been stripped off over the years of "development". For example, the earlier cars had more little rubber pads to stop the bonnet rubbing on the wings. The older starter handle had the coil on it to make it easier on your hands when turning the engine over. The later ones can cause friction burns, but were cheaper and easier to make. By the way, the plural of Dyane is Dyanes. Of course, you can talk about your Dyane's starter handles. |
|
| Author: | Rhythm Thief [ November 27th, 2011, 7:28 pm ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
Or indeed your Dyanes' starter handles. If you have more than one Dyane ... 
|
|
| Author: | Sean [ November 27th, 2011, 11:13 pm ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
the cross member from the b pillars was "developed" too from a robust piece of chunkyness to a 2cv like flimsiness. |
|
| Author: | samfieldhouse [ November 29th, 2011, 9:31 am ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
I know nothing about Dyanes or Dyane Spares but I do know about apostrophes. Code: Anyone know anything about Dyanes?
|
|
| Author: | Neil [ November 29th, 2011, 9:49 am ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
samfieldhouse wrote: I know nothing about Dyanes or Dyane Spares but I do know about apostrophes. samfieldhouse wrote: so it's definately due a new bulkhead. Definitely* 
|
|
| Author: | J-dub [ November 29th, 2011, 10:00 am ] |
| Post subject: | Re: any one know anything about dyane's? and some parts? |
I always put difiantly
|
|
| Page 1 of 2 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|