| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 99 of 105 |
| Author: | subarupete [ April 27th, 2020, 2:10 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Front strut first fitting, seems to be ok? The tie rod just clears the bottom of the strut. Attachment: DC3F6B2C-422A-47EB-8C18-0A5C9CAA9F3F.jpeg [ 899.51 KiB | Viewed 5404 times ] Height of strut may require a dimple in the bonnet:( Attachment: CCD4EFA6-BCFF-49D4-AB35-1F33A99BEB85.jpeg [ 823.01 KiB | Viewed 5404 times ] |
|
| Author: | subarupete [ April 30th, 2020, 1:32 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Diff/transfer box done with mods and correct clutch release bearing!! Attachment: 3A62FB87-C981-4C21-A4B1-BD97DBCE2946.jpeg [ 827.43 KiB | Viewed 5368 times ] |
|
| Author: | subarupete [ May 4th, 2020, 1:53 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Repositioned one of the front struts, all works ok for clearance and is softer. But see pics of the subframe?? Its a bit of a mess, so have ordered some new steel, will attempt to design/fabricate a tidier frame:) Attachment: 9A317C76-9F94-41DF-B2F4-ED27860D27F4.jpeg [ 826.16 KiB | Viewed 5313 times ] Attachment: 89D472B2-D220-4C6D-859F-2F1647FB30FF.jpeg [ 437.37 KiB | Viewed 5313 times ] |
|
| Author: | subarupete [ May 23rd, 2020, 12:15 pm ] | ||
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 | ||
Have made a strut that has the spring working, irrespective of suspension height. Parts required... Attachment: 4BEC51AE-348C-45BD-B6CB-39787C3ACA31.jpeg [ 443.33 KiB | Viewed 5016 times ] Front view... Attachment: 8525F40F-F454-40DA-89F8-FAEE95FEAC91.jpg [ 35.58 KiB | Viewed 5019 times ] Side view... The top mount sits half way down inside the spring and the hydraulic ram is attached there.
|
|||
| Author: | subarupete [ June 24th, 2020, 11:34 am ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
First fit of revised suspension, it’s fits!. Need to add hand-brake bracket and brackets for the battery box and exhaust. Then (this time) will take it all apart to paint the whole front end properly. Attachment: 9A77A90B-E059-4CED-B66B-9AE66A86198E.jpeg [ 427.78 KiB | Viewed 4542 times ] |
|
| Author: | lpgo [ June 24th, 2020, 9:23 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
I was just thinking, whats the name of your suspension.. Hydropneumaticcoilovers I guess. I like it all.. |
|
| Author: | subarupete [ June 25th, 2020, 8:12 am ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Hi Lpgo, Where have you been hiding. Rear End. Citroen C5 strut with 2cv rear springs coil over. Front End. Hydraulic ram 4ton with 2cv front springs , not really coil over as they are in “series” such that the springs always functions. However at the front the top bar bends and is bent:) at some point in testing???, needs to be larger section and thicker wall. |
|
| Author: | lpgo [ June 25th, 2020, 9:42 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Stil reading almost every post on here. Made another lowered 2cv which I'm trying to sell at the moment but it seems people are holding the money in the pocket do to Corona.. |
|
| Author: | subarupete [ June 25th, 2020, 9:59 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
New Topic....? |
|
| Author: | Edce [ June 28th, 2020, 10:04 am ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
I have been thinking (way back btw) about the mounting of airbags. Would be possible if I compare it with your construction, because they are much smaller. I hesitated because our technical safety controls by the authorities would disapprove it because not being original. I do not know if the airbags (small because lightweight vehicle) would fit inside a spring box, and can be hided for the eye of the inspector 
|
|
| Page 99 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|