| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 98 of 105 |
| Author: | lpgo [ April 16th, 2020, 12:10 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
subarupete wrote: Wow views of 127203, sadly 50% are probably "bots". Well keep the posts comming then... |
|
| Author: | subarupete [ April 16th, 2020, 1:54 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Road car is ready to MOT---- Steering done, new carb (emissions were Bad), lights fixed. But MOT's hold for non essential cars etc. So some updates soon on the 4x4 |
|
| Author: | Geert [ April 16th, 2020, 8:02 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Good luck !!! |
|
| Author: | subarupete [ April 19th, 2020, 4:20 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
The saga begins.. Attachment: P1000675.jpg [ 330.47 KiB | Viewed 4434 times ] The transfer box/Diff problem, (I think !?). Attachment: P1000676 (1).jpg [ 171.85 KiB | Viewed 4434 times ] The solution..... Attachment: P1000677 (1).jpg [ 183.3 KiB | Viewed 4434 times ] |
|
| Author: | subarupete [ April 22nd, 2020, 2:30 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Engine and box out, rear gears dismantled, appear to be well lubricated.... Attachment: A0FF72D5-C00D-4C59-9001-E304B5FF1603.jpeg [ 838.47 KiB | Viewed 4384 times ] |
|
| Author: | subarupete [ April 23rd, 2020, 5:23 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
The whole saga began. Test drove the car, up the road and round the field. All went well... Let the car stand for about 5 weeks + started the car , nasty sound from gearbox, push the clutch to the floor, noise stopped, let clutch up noise come back. ASSUMED it was the input shaft bearing!!! Have examined the clutch housing, it was clean when it got assembled and had been used before. The bell housing has some black dust and some aluminuim filings??? Will look at clutch and release bearing. The saga continues, took the box apart, all the bearings have oil and so no signs of running dry? But have modified the box anyway... Before modification. Attachment: IMG_0074.jpg [ 404.65 KiB | Viewed 4353 times ] Modified box Attachment: IMG_0077.jpg [ 384.56 KiB | Viewed 4353 times ] |
|
| Author: | subarupete [ April 24th, 2020, 3:36 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Progess today.... Attachment: P1000678.jpg [ 248.09 KiB | Viewed 4336 times ] |
|
| Author: | subarupete [ April 25th, 2020, 5:38 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
Another modification/addition. Attachment: A0DE8AA2-DC1C-464F-9EC2-A3CDC089F26E.jpeg [ 617.65 KiB | Viewed 4316 times ] |
|
| Author: | rob massey55 [ April 25th, 2020, 5:56 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
You're into the world of the sublime Pete  Good stuff! |
|
| Author: | subarupete [ April 26th, 2020, 2:23 pm ] |
| Post subject: | Re: �Make Your Own ....2CV.... 4x4 |
While I have the engine and box out, I am trying to see if I can move the struts. Currently even with softer springs the front is too hard. Move the strut bottom mount to miss the steering and fit under the bonnet, needs some carful measurements!! Short bottom mount. Attachment: 248CF61A-CC25-4C04-B227-35E139B9EDAD.jpeg [ 473.91 KiB | Viewed 4296 times ] Pivot point to miss the steering tie rod? Yellow line is the sweet spot. Attachment: 4D54EC4E-B3DA-4E56-83A4-0C49C0C107FD.jpeg [ 442.29 KiB | Viewed 4296 times ] |
|
| Page 98 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|