International2cvFriends.com
http://www.international2cvfriends.com/forum/

Make Your Own ....2CV.... 4x4
http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279		 Page 95 of 105
Author:  subarupete [ July 16th, 2019, 1:23 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Wiring in the Car.

Attachment:
P1000508.jpg
P1000508.jpg [ 350.58 KiB | Viewed 5999 times ]


Wiring under the Bonnet.

Attachment:
P1000509.jpg
P1000509.jpg [ 371.6 KiB | Viewed 5999 times ]


Wiring ToDo Basics.
Headlamps, Side, Indicators, Horn.
New Battery +VE and connections to main loom.
Extras bits +++.
Author:  subarupete [ July 23rd, 2019, 5:48 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Fuel Tank Fitted.

Base is bolted to the floor and to the inner wing.

Attachment:
P1000510.jpg
P1000510.jpg [ 284.05 KiB | Viewed 5961 times ]
Author:  subarupete [ August 19th, 2019, 3:21 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
New main gearbox lever and try out for the Transfer box lever, new mount to be fabricated.


Attachment:
P1000529.jpg
P1000529.jpg [ 310.81 KiB | Viewed 5807 times ]


Revised shift pattern

Attachment:
P1000535.jpg
P1000535.jpg [ 143.5 KiB | Viewed 5807 times ]



Transfer box end of gear lever.

Attachment:
P1000533.jpg
P1000533.jpg [ 316.78 KiB | Viewed 5807 times ]
Author:  subarupete [ August 20th, 2019, 3:15 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Gear Lever (Scratch Head Moment's)

Transfer box new lever.
Now vertical, needs sanding and paint.

Attachment:
P1000536.jpg
P1000536.jpg [ 311.37 KiB | Viewed 5795 times ]


Attachment:
P1000537.jpg
P1000537.jpg [ 323.24 KiB | Viewed 5795 times ]



Lever End.

Mount for the lever and linkage that doesn't interfere with the seats or the seat rails

Attachment:
P1000539.jpg
P1000539.jpg [ 236.62 KiB | Viewed 5795 times ]
Author:  subarupete [ August 21st, 2019, 5:16 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Transfer box Lever.

Mounted to the same bit of chassis as the rear gear box support.
Need the nuts to be recessed as the foul the lever a bit.

Attachment:
P1000540.jpg
P1000540.jpg [ 242.75 KiB | Viewed 5778 times ]



Both ends now connected and it allows selection!


Attachment:
P1000543.jpg
P1000543.jpg [ 298.4 KiB | Viewed 5778 times ]
Author:  subarupete [ August 22nd, 2019, 3:34 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Transfer Box new knob

Revised pattern due to the linkage used,

Attachment:
P1000546.jpg
P1000546.jpg [ 198.52 KiB | Viewed 5761 times ]


Final Mounting (famous last words)

Slot cut out to clear seat frame.

Attachment:
P1000544.jpg
P1000544.jpg [ 235.55 KiB | Viewed 5761 times ]
Author:  lpgo [ August 22nd, 2019, 4:46 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
I.m still not sure which way round..
Design follows function or function follows design...


Hmmmmm...

Well the result is looking awsome.. (at least in my eyes).
Author:  subarupete [ August 22nd, 2019, 5:56 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Thanks Geo,

Hope to test it on the road (track) soon.

Need to fix the LDS pump/pipes/wiring for the suspension so it has some damping, at the moment the rear is like a Kangaroo.

Had is running a number of times, vibrates as the engine mounts are (through)bolted, when I carefully engage the clutch, more vibration from the extra shaft :( , gave it lots of revs and it has stayed together :)
Author:  subarupete [ August 29th, 2019, 6:04 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Tight fit for gear lever.

Attachment:
P1000549.jpg
P1000549.jpg [ 198.48 KiB | Viewed 5689 times ]


Support for LDS tank.

Attachment:
P1000548.jpg
P1000548.jpg [ 269.89 KiB | Viewed 5689 times ]
Author:  rob massey55 [ August 29th, 2019, 6:45 pm ]
Post subject:  Re: Make Your Own ....2CV.... 4x4
Well it's not like you'll be racing through the gears :)
Loving this build 8-)
Page 95 of 105 All times are UTC + 1 hour [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/