Have had thoughts about reaming the hole out, but the reamer size I can buy is 4.99mm
Thats leaves .01 mm which is still too much for a friction fit with hardened pins
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 92 of 105 |
| Author: | subarupete [ May 12th, 2019, 5:26 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Have had thoughts about reaming the hole out, but the reamer size I can buy is 4.99mm Thats leaves .01 mm which is still too much for a friction fit with hardened pins
|
|
| Author: | subarupete [ May 14th, 2019, 10:47 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Engine together with diff (gearbox) out of the car. Attachment: modify.jpg [ 193.38 KiB | Viewed 4323 times ] |
|
| Author: | subarupete [ May 14th, 2019, 4:53 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Before, During and After. Attachment: P1000409.jpg [ 356.03 KiB | Viewed 4314 times ] Attachment: P1000417.jpg [ 196.77 KiB | Viewed 4314 times ] Attachment: P1000418.jpg [ 139.01 KiB | Viewed 4314 times ] Attachment: P1000419.jpg [ 173.92 KiB | Viewed 4314 times ] |
|
| Author: | subarupete [ May 21st, 2019, 12:36 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Re-assembled the rear cover with Loctite gasket and then saw the bearing, missing one ball bearing!!! Dismantled it all to check, all the other bearings are OK  The last bearing fits from the outside and is held in place by the oil seal cover. Attachment: P1000444.jpg [ 254.29 KiB | Viewed 4283 times ] Balls up! Attachment: P1000445.jpg [ 173.49 KiB | Viewed 4283 times ] |
|
| Author: | rob massey55 [ May 21st, 2019, 7:31 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
So let me get this right Pete, you're one ball bearing short of a 2cv 4x4 
|
|
| Author: | subarupete [ May 21st, 2019, 8:42 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
 ps I found it on the floor! |
|
| Author: | Roger V [ May 21st, 2019, 8:56 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Mine was under the sofa! |
|
| Author: | subarupete [ May 22nd, 2019, 10:34 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Front Diff(Gearbox) reassembled and ready to refit. HOWEVER! Have found the steering rack has a very nasty "clack" and is also to loose. For me that is a real bummer to get under the car to remove and solve issue and refit, but the weather is good at the moment
|
|
| Author: | subarupete [ May 23rd, 2019, 11:10 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Had not tensioned the plunger correctly Attachment: Untitled.jpg [ 128.99 KiB | Viewed 4243 times ] ps Sack the old fart that overlooked it
|
|
| Author: | Roger V [ May 23rd, 2019, 11:44 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Was it easily accessible? |
|
| Page 92 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|