Small bit of turning done.
Attachment:
P1000050.jpg [ 138.26 KiB | Viewed 4475 times ]
Attachment:
P1000051.jpg [ 189.19 KiB | Viewed 4475 times ]
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 86 of 105 |
| Author: | subarupete [ August 15th, 2018, 2:11 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Small bit of turning done. Attachment: P1000050.jpg [ 138.26 KiB | Viewed 4475 times ] Attachment: P1000051.jpg [ 189.19 KiB | Viewed 4475 times ] |
|
| Author: | lpgo [ August 15th, 2018, 6:39 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
subarupete wrote: Small bit of turning done. Attachment: P1000050.jpg Attachment: P1000051.jpg Now comes the difficult part.. Welding it strait together.. So far looking good.. |
|
| Author: | subarupete [ August 31st, 2018, 11:11 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Tig Welded, very tidy and straight. Attachment: P1000098.jpg [ 99.1 KiB | Viewed 4425 times ] Attachment: P1000099.jpg [ 143.08 KiB | Viewed 4425 times ] |
|
| Author: | lpgo [ August 31st, 2018, 5:59 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
subarupete wrote: Tig Welded and straight. . Rpm don,t forgive, only high rpm will tell if it is straight.. |
|
| Author: | Roger V [ August 31st, 2018, 11:36 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Looking good 
|
|
| Author: | subarupete [ September 1st, 2018, 12:51 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Now with the UJ's fitted. Attachment: P1000102.jpg [ 49.2 KiB | Viewed 4393 times ] |
|
| Author: | subarupete [ September 1st, 2018, 4:42 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Painted and fitted in place. Connects between Main/Clutch shaft and input shaft of the remote gearbox. Attachment: P1000103.jpg [ 236.25 KiB | Viewed 4389 times ] Attachment: P1000104.jpg [ 310.53 KiB | Viewed 4389 times ] |
|
| Author: | rob massey55 [ September 1st, 2018, 6:47 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
That lump of metal that the adjustable spanner is sitting on, what's that for? .
|
|
| Author: | subarupete [ September 1st, 2018, 6:57 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
An over-weight chassis? |
|
| Author: | rob massey55 [ September 1st, 2018, 7:47 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
 surely not  .
|
|
| Page 86 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|