| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 85 of 105 |
| Author: | subarupete [ February 22nd, 2018, 8:57 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Not that many days and its going to be very cold next week:) |
|
| Author: | rob massey55 [ February 22nd, 2018, 8:59 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
10mm.'s better than nowt! now the workshop's spotless, Crack on  .subarupete wrote: Ooh clean floor!. Fitted the front diff prop shafts, they fit but very tight near the gearbox about 10mm clearance. Attachment: IMG_2061 (1).jpg |
|
| Author: | subarupete [ February 23rd, 2018, 7:33 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Unexpected problems do occur or is it bad planning:) The input shaft to the remote gearbox had some play, had a look at the seal found it was a bad condition. Chevronics do a seal (££££) for GS/GSA boxes but the LN is about 1.5mm larger! So a bit of milling it was substituted sealed bearing. We will have to see if its OK. Input Shaft. Attachment: IMG_2065.jpg [ 71.65 KiB | Viewed 5144 times ] Old Seal. Attachment: IMG_2062.jpg [ 74.1 KiB | Viewed 5144 times ] New Bearing in place. Attachment: IMG_2064.jpg [ 71.86 KiB | Viewed 5144 times ] |
|
| Author: | subarupete [ February 26th, 2018, 2:52 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
The list of things to do, should get shorter. However it seems that the plan to use a standard exhaust with cross-box wont fit:( Bigger calipers + the rear plate of the diff gets in the way. Attachment: IMG_2084.jpg [ 94.98 KiB | Viewed 5128 times ] Plan to fabricate an exhaust from mandrel bends...2 into 1 very sporty? Red lines show the plan, but as we are all very aware "Red Lines" can change or even disappear!!! Attachment: IMG_2080.jpg [ 478.88 KiB | Viewed 5128 times ] |
|
| Author: | subarupete [ March 18th, 2018, 11:03 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Can't make the exhaust till the body is sitting on the chassis and can't do that until I have a transfer shaft fitted. What is required, "the middle part". But, not happy with getting it welded. Attachment: IMG_2111.jpg [ 298.07 KiB | Viewed 5056 times ] So have to machine one!! Purchased a bit of steel.. Attachment: IMG_2130.jpg [ 252.62 KiB | Viewed 5056 times ] Some difficult milling/turning/drilling and lot of Google. Bit of a challenge but nothing ventured..... |
|
| Author: | lpgo [ April 8th, 2018, 11:19 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Did you go to Morvan?? |
|
| Author: | subarupete [ April 9th, 2018, 8:31 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Hi Geo, Nope, the car was not finished:( |
|
| Author: | subarupete [ August 2nd, 2018, 10:11 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Hi all, Back again after a long period of no work on the off-road car or the road car. Turning & Milling required to join the two uj's to make the shaft between the clutch shaft and the remote gearbox. Attachment: IMG_2112.jpg [ 317.37 KiB | Viewed 4654 times ] Attachment: IMG_3436.jpg [ 140.12 KiB | Viewed 4654 times ] |
|
| Author: | rob massey55 [ August 2nd, 2018, 10:14 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Good to see you back on it Pete  .
|
|
| Author: | Roger V [ August 2nd, 2018, 10:52 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Yep +1 
|
|
| Page 85 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|