| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 84 of 105 |
| Author: | subarupete [ February 9th, 2018, 12:54 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Discs now fitted and different brace (x2) allows drive shaft clearance. Attachment: IMG_2007.jpg [ 291.57 KiB | Viewed 4632 times ] Whoopee, only two oil leaks. Need a copper washer under the sump nut. Attachment: IMG_2012.jpg [ 217.23 KiB | Viewed 4632 times ] And a seal?? for the splined prop shaft flange?? Attachment: IMG_2011.jpg [ 307.64 KiB | Viewed 4632 times ] |
|
| Author: | lpgo [ February 9th, 2018, 2:16 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
subarupete wrote: Whoopee, only two oil leaks. Great job you did then... |
|
| Author: | jasu [ February 9th, 2018, 3:04 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
subarupete wrote: And a seal?? for the splined prop shaft flange?? Attachment: IMG_2011.jpg On Land-Rover there is felt under the nut at flange. And many put also some sealing/glue to splines to avoid leaking... Nicely done when there isn't any other leaks..! |
|
| Author: | subarupete [ February 9th, 2018, 3:51 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Thanks guys. |
|
| Author: | jasu [ February 9th, 2018, 4:05 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
 Part no 5 on that picture... |
|
| Author: | subarupete [ February 9th, 2018, 5:08 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Something like this... Perhaps make it from felt or soft rubber? Attachment: 2_image.jpg [ 9.29 KiB | Viewed 4618 times ] |
|
| Author: | subarupete [ February 15th, 2018, 5:15 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Fitted the centre bearing for the front prop shafts. Attachment: IMG_2030.jpg [ 296.12 KiB | Viewed 4597 times ] Shortened the first of two prop shafts, combination of suzuki/truimph-herald bits. Attachment: IMG_2039.jpg [ 275.47 KiB | Viewed 4597 times ] |
|
| Author: | subarupete [ February 17th, 2018, 4:58 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
The first on and even painted it... Attachment: IMG_2052.jpg [ 292.8 KiB | Viewed 4584 times ] |
|
| Author: | subarupete [ February 22nd, 2018, 5:17 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Ooh clean floor!. Fitted the front diff prop shafts, they fit but very tight near the gearbox about 10mm clearance. Attachment: IMG_2061 (1).jpg [ 84.88 KiB | Viewed 4562 times ] |
|
| Author: | lpgo [ February 22nd, 2018, 8:04 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Only 5 weeks to Morvan.... you should hurry.... |
|
| Page 84 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|