| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 83 of 105 |
| Author: | subarupete [ January 20th, 2018, 3:41 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Fitted Engine and front diff into the chassis. Couple of issues, the front of the engine is to high, which makes the transfer shaft slope down at the rear. Will need to make some other engine mounts, to allow the front to sit lower... Attachment: IMG_1699.jpg [ 316.84 KiB | Viewed 4259 times ] Attachment: IMG_1703.jpg [ 303.82 KiB | Viewed 4259 times ] Braces for the front struts need "redoing" to allow drive shaft to clear. Attachment: IMG_1702.jpg [ 232.15 KiB | Viewed 4259 times ] |
|
| Author: | subarupete [ January 21st, 2018, 1:44 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Lack of space for revised engine mounts  Attachment: IMG_1707.jpg [ 280.54 KiB | Viewed 4243 times ] Will need to shorten the rear mounts. Attachment: IMG_1708.jpg [ 337.22 KiB | Viewed 4243 times ] |
|
| Author: | subarupete [ January 26th, 2018, 1:22 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Engine, Bell housing, clutch and front diff in place. It all fits and shafts don't foul any where  With a bit more looking, pondering, thinking have decided to use the engine mounts as they were intended. Just need to redo the remote gearbox mounts so that the transfer shafts line up. Attachment: IMG_1942.jpg [ 415.15 KiB | Viewed 4223 times ] Attachment: IMG_1943.jpg [ 407.92 KiB | Viewed 4223 times ] Attachment: IMG_1950.jpg [ 353.19 KiB | Viewed 4223 times ] |
|
| Author: | subarupete [ January 30th, 2018, 5:44 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Bit of a cock-up, forgot to put cut outs in the Bell housing to allow the discs to clear. Will do it in-situ, have reduced the diameter of the discs by about 10mm. This is what Joolz did in use Red One... Attachment: SDC10884.jpg [ 116.42 KiB | Viewed 4196 times ] |
|
| Author: | rob massey55 [ January 30th, 2018, 7:03 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Fair enough, do you weld in pieces to keep the mud out? |
|
| Author: | subarupete [ January 30th, 2018, 7:48 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Could do, but there is a huge hole for the clutch cable... |
|
| Author: | rob massey55 [ January 30th, 2018, 8:45 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Aah! you seem to know what you're doing  .
|
|
| Author: | subarupete [ January 31st, 2018, 6:10 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
One Side done, now to do the other side and find the brake Disc! Attachment: IMG_1968.jpg [ 261.68 KiB | Viewed 4173 times ] Cock Up number.... The diagonal Strut support is in the wrong place:) |
|
| Author: | rob massey55 [ January 31st, 2018, 8:25 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Yeah but prototypes are always like that, after you've done the next one you'll have it all sorted .
|
|
| Author: | subarupete [ February 8th, 2018, 5:13 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Two welds forward one weld back... As the remote gearbox need to align with the transfer shaft had to adjust the 2 side mounts and remove the rear lower mount and fit a mount at the top, not very pretty but will be painted. Old Mount. Attachment: IMG_1307.jpg [ 430.46 KiB | Viewed 4140 times ] New Mount. Attachment: IMG_1992.jpg [ 369.12 KiB | Viewed 4140 times ] |
|
| Page 83 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|