It would give "Ice Road Truckers" some worries
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 81 of 105 |
| Author: | subarupete [ October 3rd, 2017, 11:58 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
It would give "Ice Road Truckers" some worries
|
|
| Author: | subarupete [ October 3rd, 2017, 4:17 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Latest Bit of Kit. Elliott Dividing Head. Attachment: IMG_1425.jpg [ 277.39 KiB | Viewed 4231 times ] Large, heavy and very, very old school, plan to see if I can cut some splines onto a shaft, it's a bit of a diversion, from the build. |
|
| Author: | lpgo [ October 3rd, 2017, 5:15 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Yet another butterfly moment I guess..... Me jealous... subarupete wrote: Latest Bit of Kit. Elliott Dividing Head. Attachment: IMG_1425.jpg Large, heavy and very, very old school, plan to see if I can cut some splines onto a shaft, it's a bit of a diversion, from the build. |
|
| Author: | rob massey55 [ October 3rd, 2017, 6:30 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
What Milling machine have you got ? |
|
| Author: | subarupete [ October 3rd, 2017, 6:54 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Myford, brill for Alumiuim, paitence requird for steel. |
|
| Author: | rob massey55 [ October 3rd, 2017, 7:24 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
That Div. head looks flamin' heavy, will it fit on the table ok? |
|
| Author: | subarupete [ October 3rd, 2017, 8:06 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
As you say F'in heavy, haven't lifted it up and put it the mill table yet! It has a proper Tail stock so I can off-set it some what. Would ft a Bridgeport OK  dreaming.......
|
|
| Author: | rob massey55 [ October 4th, 2017, 9:07 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Make sure the machine and table is well supported then  . https://www.youtube.com/watch?v=UVHUphU18KM
|
|
| Author: | subarupete [ October 5th, 2017, 8:59 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Were you driving?
|
|
| Author: | rob massey55 [ October 22nd, 2017, 3:17 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
 vida1 by Robndaisy, on FlickrThis one. Press on image and should play as a video clip. |
|
| Page 81 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|