Jeez Pete, you're well into it now! The flaming thing should be strong enough.
You're not planning on dropping it out of a helicopter ...are you
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 79 of 105 |
| Author: | rob massey55 [ July 31st, 2017, 7:03 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Jeez Pete, you're well into it now! The flaming thing should be strong enough. You're not planning on dropping it out of a helicopter ...are you
|
|
| Author: | subarupete [ July 31st, 2017, 8:10 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Over Engineering is easier to do, some of my previous work broke or bent, but in my defence off-roading does test things to the limit. |
|
| Author: | subarupete [ August 1st, 2017, 4:24 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Gear Levers... Attachment: IMG_1264.jpg [ 289.25 KiB | Viewed 4366 times ] |
|
| Author: | subarupete [ August 11th, 2017, 6:28 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Remote Gearbox bits. Attachment: IMG_1290.jpg [ 276.59 KiB | Viewed 4317 times ] Attachment: IMG_1291.jpg [ 262.53 KiB | Viewed 4317 times ] |
|
| Author: | subarupete [ August 16th, 2017, 3:07 pm ] | ||
| Post subject: | Re: Make Your Own ....2CV.... 4x4 | ||
Fitting the Floors! Attachment: IMG_1306.jpg [ 392.83 KiB | Viewed 4285 times ] https://youtu.be/ZuLqfQC3KSY See https://youtu.be/ZuLqfQC3KSY
|
|||
| Author: | subarupete [ August 24th, 2017, 2:49 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Transmission Tunnel? Re-used the old floors and gearbox cover. Make do and mend as the saying goes. Attachment: IMG_1313.jpg [ 435.9 KiB | Viewed 4257 times ] Attachment: IMG_1314.jpg [ 342.76 KiB | Viewed 4257 times ] |
|
| Author: | subarupete [ September 1st, 2017, 4:12 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Oil Seal Plates for the Front Diff. Over zealous with the Mill  Attachment: IMG_1332.jpg [ 271.59 KiB | Viewed 4218 times ] |
|
| Author: | subarupete [ September 7th, 2017, 1:56 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Lots of Lathe/Mill/Drill/Gears/Bearings etc.. Front Diff is almost complete. Attachment: IMG_1333.jpg [ 340.78 KiB | Viewed 4193 times ] Attachment: IMG_1334.jpg [ 330.59 KiB | Viewed 4193 times ] |
|
| Author: | rob massey55 [ September 7th, 2017, 7:39 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Beautiful! 
|
|
| Author: | subarupete [ September 13th, 2017, 2:45 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Attachment: IMG_1343.jpg [ 376.42 KiB | Viewed 4150 times ] |
|
| Page 79 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|