Forgot about the Fuel Tank, so no 3rd seat.
Also fitted LDS tank and pump, high up as they are Splash-proof but not Water-proof.
Attachment:
IMG_1179.jpg [ 376.73 KiB | Viewed 4050 times ]
| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 78 of 105 |
| Author: | subarupete [ July 8th, 2017, 7:24 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Good point:) |
|
| Author: | subarupete [ July 12th, 2017, 4:27 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Forgot about the Fuel Tank, so no 3rd seat. Also fitted LDS tank and pump, high up as they are Splash-proof but not Water-proof. Attachment: IMG_1179.jpg [ 376.73 KiB | Viewed 4050 times ] |
|
| Author: | rob massey55 [ July 12th, 2017, 8:03 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Starting to remind me of something... http://www.spacekids.co.uk/rover/ Coming together Pete. |
|
| Author: | subarupete [ July 14th, 2017, 4:59 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Finished mounting brackets for the Transfer Box and painted the chassis. Attachment: IMG_1189.jpg [ 317.29 KiB | Viewed 4029 times ] Transfer box fitted. Attachment: IMG_1191.jpg [ 259.78 KiB | Viewed 4029 times ] ps Rob Mine has not been designed to "un-fold" (see Apollo vids). It may "fold" but for a different reason 
|
|
| Author: | subarupete [ July 17th, 2017, 3:15 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Now comes the part which causes some worries, the alignment of the Engine/Clutch/Diff casing with the remote gearbox. Measurements - Try Out. Engine is set as low as can be in the chassis, Clutch shaft with UJ clears the top of the cross tube by 10mm. The front prop shaft clears the tie-rod and cross tube by 10mm. The Kawasaki prop shaft is slopes down a little, because the back of the front diff box sits down by 15/20mm in relation to the engine. I will see if I can drop the engine down 15/20mm to compensate, with out the sump protruding below the chassis line. It should all fit together and work Attachment: IMG_1200.jpg [ 419.5 KiB | Viewed 4002 times ] Attachment: IMG_1201.jpg [ 384.9 KiB | Viewed 4002 times ] Attachment: IMG_1202.jpg [ 315.57 KiB | Viewed 4002 times ] Attachment: IMG_1203.jpg [ 344.79 KiB | Viewed 4002 times ] |
|
| Author: | subarupete [ July 19th, 2017, 1:28 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Gear Box Brackets. As the casing is LN, will re-use those mounting points at the sides. Attachment: IMG_1205.jpg [ 287.67 KiB | Viewed 3988 times ] For the Rear, just going to copy how Citroen did it, need to remake the Oil Seal plate much longer and bolt the bush support to it. Attachment: IMG_1207.jpg [ 233.76 KiB | Viewed 3988 times ] Using Transit bushes, very cheap:), hope they don't fail:( |
|
| Author: | subarupete [ July 22nd, 2017, 2:49 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
New extended gearbox mount. Attachment: IMG_1212.jpg [ 275.61 KiB | Viewed 3970 times ] Attachment: IMG_1213.jpg [ 290.9 KiB | Viewed 3970 times ] |
|
| Author: | subarupete [ July 26th, 2017, 2:58 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Gearbox Side Brackets. Attachment: IMG_1233.jpg [ 350.65 KiB | Viewed 3939 times ] Attachment: IMG_1235.jpg [ 373.36 KiB | Viewed 3939 times ] Attachment: IMG_1239.jpg [ 322.3 KiB | Viewed 3939 times ] |
|
| Author: | subarupete [ July 27th, 2017, 5:13 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
More Support Brackets this time for the back of the front differential. Also have to make some revised brackets for the engine mounts, Chassis Support Attachment: IMG_1240.jpg [ 48 KiB | Viewed 3916 times ] Left Side attachment point. Attachment: IMG_1242.jpg [ 281.75 KiB | Viewed 3916 times ] Right Side attachment point. Attachment: IMG_1243.jpg [ 301.12 KiB | Viewed 3916 times ] |
|
| Author: | subarupete [ July 31st, 2017, 4:31 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Ended up with the brackets on the back of the rear plate. The mounts on the chassis will be bolted on, so that spacers can be used to set the correct height of the box. At the moment all the shafts have clearance? Left hand mount was hard to measure, fabricate and fix, Right hand side Very Hard.... as there is not much room. Attachment: IMG_1262.jpg [ 351.61 KiB | Viewed 3886 times ] Left Hand Side. Attachment: IMG_1259.jpg [ 364.72 KiB | Viewed 3886 times ] Right Hand Side. Attachment: IMG_1260.jpg [ 342.78 KiB | Viewed 3886 times ] |
|
| Page 78 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|