| International2cvFriends.com http://www.international2cvfriends.com/forum/ |
|
| Make Your Own ....2CV.... 4x4 http://www.international2cvfriends.com/forum/viewtopic.php?f=19&t=3279 |
Page 71 of 105 |
| Author: | Harley [ February 16th, 2017, 11:34 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Thanks for the info guys, The reason I am looking at a lower ratio is that I have 155/80 R15 tyres, and with the LNA gearbox it is really to long. AlthoughI will be fitting the Visa engine some time... For slower climbing I think the lower ratio will be much better. So practically, if i did get a custom crownwheel and pinion made, how difficult would it be to install in the gearbox? It has been a while since I had the gearbox apart... Cheers |
|
| Author: | subarupete [ February 17th, 2017, 9:55 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
The most Precise job on an A series.... Setting the Pinion "Height" and Pinion "backlash". Needs a dial gauge and some shims. Rick Pembro, Gearbox Guru is the expert. |
|
| Author: | subarupete [ February 21st, 2017, 5:08 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Milling the Back Plate. https://www.youtube.com/watch?v=qJK-YUT04rY |
|
| Author: | rob massey55 [ February 21st, 2017, 7:30 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Great work Pete, I used to mill stuff, we had an indexing head a bit like this https://www.google.co.uk/search?q=milli ... 9ksyDjE1DM: we used it to make PTO splined shafts for horticultural compost mixers. You could make your own gears when you've got five minutes 
|
|
| Author: | subarupete [ February 21st, 2017, 7:40 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
@rob massey55, thanks also that is interesting, as I can borrow an indexing head from the guys that wire erode the internal splines. The next project is to mill splines onto a shaft....so I may pick-up some hints from you 
|
|
| Author: | rob massey55 [ February 22nd, 2017, 12:28 am ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Looking forward to seeing that! |
|
| Author: | subarupete [ February 22nd, 2017, 6:14 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Acquired some Coil Over springs, will fit these over the front struts, to provide, the standard ride height. The plan being to use the LDS struts only when needed, thus the need for auto leveling should not be needed Newish Springs Attachment: IMG_0450.jpg [ 444.79 KiB | Viewed 3672 times ] |
|
| Author: | subarupete [ February 26th, 2017, 4:17 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Got the loan:) of some Large tyres. Well it now looks the part. Attachment: IMG_0462.jpg [ 417.95 KiB | Viewed 3654 times ] Attachment: IMG_0463.jpg [ 451.92 KiB | Viewed 3654 times ] |
|
| Author: | subarupete [ February 28th, 2017, 6:01 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Maximum and Minimum Attachment: Untitled.jpg [ 548.86 KiB | Viewed 3624 times ] |
|
| Author: | Harley [ February 28th, 2017, 11:02 pm ] |
| Post subject: | Re: Make Your Own ....2CV.... 4x4 |
Needs lowering...   
|
|
| Page 71 of 105 | All times are UTC + 1 hour [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|