| Author |
Message |
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2146
Location: Near Monmouth
|
 Re: Make Your Own ....2CV.... 4x4 It would give "Ice Road Truckers" some worries 
|
| October 3rd, 2017, 11:58 am |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2146
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Latest Bit of Kit. Elliott Dividing Head. Attachment:
IMG_1425.jpg [ 277.39 KiB | Viewed 4201 times ]
Large, heavy and very, very old school, plan to see if I can cut some splines onto a shaft, it's a bit of a diversion, from the build.
|
| October 3rd, 2017, 4:17 pm |
|
|
|
lpgo
Firing on 1-2 Spark
Joined: November 8th, 2009, 5:42 pm
Posts: 2846
Location: NL
|
Re: Make Your Own ....2CV.... 4x4 Yet another butterfly moment I guess..... Me jealous... subarupete wrote: Latest Bit of Kit. Elliott Dividing Head. Large, heavy and very, very old school, plan to see if I can cut some splines onto a shaft, it's a bit of a diversion, from the build.
_________________
Russell wrote: Hi Geo,
you've been one of the sites biggest attractions in recent years.
Russ
|
| October 3rd, 2017, 5:15 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4 What Milling machine have you got ?
|
| October 3rd, 2017, 6:30 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2146
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Myford, brill for Alumiuim, paitence requird for steel.
|
| October 3rd, 2017, 6:54 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4 That Div. head looks flamin' heavy, will it fit on the table ok?
|
| October 3rd, 2017, 7:24 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2146
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 As you say F'in heavy, haven't lifted it up and put it the mill table yet! It has a proper Tail stock so I can off-set it some what. Would ft a Bridgeport OK  dreaming.......
|
| October 3rd, 2017, 8:06 pm |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4 Make sure the machine and table is well supported then  . https://www.youtube.com/watch?v=UVHUphU18KM
|
| October 4th, 2017, 9:07 pm |
|
|
|
subarupete
Firing on two.
Joined: March 5th, 2009, 6:23 pm
Posts: 2146
Location: Near Monmouth
|
Re: Make Your Own ....2CV.... 4x4 Were you driving?
|
| October 5th, 2017, 8:59 am |
|
|
|
rob massey55
Firing on two.
Joined: December 21st, 2014, 7:33 pm
Posts: 869
Location: Rhayader Mid Wales
|
Re: Make Your Own ....2CV.... 4x4  vida1 by Robndaisy, on Flickr This one. Press on image and should play as a video clip.
|
| October 22nd, 2017, 3:17 pm |
|
|
